Copyright 1989 AT&T
Copyright (c) 1995, Sun Microsystems, Inc. All Rights Reserved
The contents of this file are subject to the terms of the Common Development and Distribution License (the "License"). You may not use this file except in compliance with the License.
You can obtain a copy of the license at usr/src/OPENSOLARIS.LICENSE or http://www.opensolaris.org/os/licensing. See the License for the specific language governing permissions and limitations under the License.
When distributing Covered Code, include this CDDL HEADER in each file and include the License file at usr/src/OPENSOLARIS.LICENSE. If applicable, add the following below this CDDL HEADER, with the fields enclosed by brackets "[]" replaced with your own identifying information: Portions Copyright [yyyy] [name of copyright owner]
#include <sys/types.h> #include <sys/mman.h> #include <sys/param.h> #include <sys/vm.h> #include <sys/ddi.h> #include <sys/sunddi.h> int prefixsegmap(dev_t dev, off_t off, struct as *asp, caddr_t *addrp, off_t len, unsigned int prot, unsigned int maxprot, unsigned int flags, cred_t *cred_p);
Architecture independent level 2 (DKI only).
Device whose memory is to be mapped.
Offset within device memory at which mapping begins.
Pointer to the address space into which the device memory should be mapped.
Pointer to the address in the address space to which the device memory should be mapped.
Length (in bytes) of the memory to be mapped.
A bit field that specifies the protections. Possible settings are: PROT_READ
Read access is desired.
Write access is desired.
Execute access is desired.
User-level access is desired (the mapping is being done as a result of a mmap(2) system call).
All access is desired.
Maximum protection flag possible for attempted mapping; the PROT_WRITE bit may be masked out if the user opened the special file read-only.
Flags indicating type of mapping. Possible values are (other bits may be set): MAP_SHARED
Changes should be shared.
Changes are private.
Pointer to the user credentials structure.
The segmap() entry point is an optional routine for character drivers that support memory mapping. The mmap(2) system call, when applied to a character special file, allows device memory to be mapped into user space for direct access by the user application.
Typically, a character driver that needs to support the mmap(2) system call supplies either an devmap(9E) entry point, or both an devmap(9E) and a segmap() entry point routine (see the devmap(9E) reference page). If no segmap() entry point is provided for the driver, devmap_setup(9F) is used as a default.
A driver for a memory-mapped device would provide a segmap() entry point if it:
needs to maintain a separate context for each user mapping. See devmap_setup(9F) for details.
needs to assign device access attributes to the user mapping.
The responsibilities of a segmap() entry point are:
Verify that the range, defined by offset and len, to be mapped is valid for the device. Typically, this task is performed by calling the devmap(9E) entry point. Note that if you are using ddi_devmap_segmap(9F) or devmap_setup(9F) to set up the mapping, it will call your devmap(9E) entry point for you to validate the range to be mapped.
Assign device access attributes to the mapping. See ddi_devmap_segmap(9F), and ddi_device_acc_attr(9S) for details.
Set up device contexts for the user mapping if your device requires context switching. See devmap_setup(9F) for details.
Perform the mapping with ddi_devmap_segmap(9F), or devmap_setup(9F) and return the status if it fails.
The segmap() routine should return 0 if the driver is successful in performing the memory map of its device address space into the specified address space.
The segmap() must return an error number on failure. For example, valid error numbers would be ENXIO if the offset/length pair specified exceeds the limits of the device memory, or EINVAL if the driver detects an invalid type of mapping attempted.
If one of the mapping routines ddi_devmap_segmap() or devmap_setup()fails, you must return the error number returned by the respective routine.
mmap (2), devmap (9E), ddi_devmap_segmap (9F), devmap_setup (9F), ddi_device_acc_attr (9S)
Writing Device Drivers