Lines Matching refs:uint8_t
115 uint8_t portNumber;
124 uint8_t setClocking; /* host requests baud rate be set */
125 uint8_t baudLo; /* host does baud divisor calculation */
128 uint8_t baudHi;
129 uint8_t prescaler; /* specified as N/8; values 8-ff are valid */
131 uint8_t txClocking; /* 0=internal, 1=external/DSR */
132 uint8_t rxClocking; /* 0=internal, 1=external/DSR */
134 uint8_t setLcr; /* host requests lcr be set */
135 uint8_t lcr; /* use PARITY, STOPBITS, DATABITS below */
137 uint8_t setFlowControl; /* host requests flow control be set */
138 uint8_t ctsFlowControl; /* 1=use CTS flow control, 0=don't */
139 uint8_t xonFlowControl; /* 1=use XON/XOFF flow control, 0=don't */
140 uint8_t xonChar; /* specified in current character format */
141 uint8_t xoffChar; /* specified in current character format */
143 uint8_t setRts; /* host requests RTS output be set */
144 uint8_t rts; /* 1=active, 0=inactive */
146 uint8_t setDtr; /* host requests DTR output be set */
147 uint8_t dtr; /* 1=on, 0=off */
155 uint8_t forwardingLength;
156 uint8_t dsrFlowControl; /* 1=use DSR flow control, 0=don't */
159 uint8_t txAckThreshold;
160 uint8_t loopbackMode; /* 0=no loopback, 1=loopback enabled */
169 uint8_t _txOn;
170 uint8_t _txOff; /* stop transmitting */
171 uint8_t txFlush; /* toss outbound data */
172 uint8_t txBreak; /* turn on break (cleared by _txOn) */
173 uint8_t rxOn; /* turn on receiver */
174 uint8_t rxOff; /* turn off receiver */
175 uint8_t rxFlush; /* toss inbound data */
178 uint8_t rxForward;
181 uint8_t returnStatus;
182 uint8_t resetDataToggle; /* reset data toggle state to DATA0 */
185 uint8_t enablePort;
188 uint8_t disablePort;
219 uint8_t portNumber; /* 0x80 */
222 uint8_t sendGlobalStatus;
223 uint8_t resetStatusToggle; /* 1=reset global status toggle */
224 uint8_t resetStatusCount; /* a cycling value */
225 uint8_t remoteWakeupEnable; /* 0x10=P1, 0x20=P2, 0x40=P3, 0x80=P4 */
226 uint8_t disableStatusMessages; /* 1=send no status until host talks */
240 uint8_t portNumber; /* 0,1,2,3 */
241 uint8_t cts; /* reports CTS pin */
242 uint8_t dcd; /* reports DCD pin */
243 uint8_t dsr; /* reports DSR pin */
244 uint8_t ri; /* reports RI pin */
245 uint8_t _txOff; /* transmit has been disabled (by host) */
248 uint8_t _txXoff;
249 uint8_t rxEnabled; /* as configured by rxOn/rxOff 1=on, 0=off */
252 uint8_t controlResponse;
253 uint8_t txAck; /* ACK (data TX complete) */
254 uint8_t rs232valid; /* RS-232 signal valid */
264 uint8_t portNumber; /* 0x80=globalStatusMessage */
265 uint8_t sendGlobalStatus; /* from request, decremented */
266 uint8_t resetStatusCount; /* as in request */
270 uint8_t portNumber; /* 0x81=globalDebugMessage */
271 uint8_t n; /* typically a count/status byte */
272 uint8_t b; /* typically a data byte */