# # CDDL HEADER START # # The contents of this file are subject to the terms of the # Common Development and Distribution License (the "License"). # You may not use this file except in compliance with the License. # # You can obtain a copy of the license at usr/src/OPENSOLARIS.LICENSE # or http://www.opensolaris.org/os/licensing. # See the License for the specific language governing permissions # and limitations under the License. # # When distributing Covered Code, include this CDDL HEADER in each # file and include the License file at usr/src/OPENSOLARIS.LICENSE. # If applicable, add the following below this CDDL HEADER, with the # fields enclosed by brackets "[]" replaced with your own identifying # information: Portions Copyright [yyyy] [name of copyright owner] # # CDDL HEADER END # # # Copyright 2006 Sun Microsystems, Inc. All rights reserved. # Use is subject to license terms. # # # The officially supported devices do not require a entry under # tape-config-list as their configuration is built in to the driver. # # # A non configured drive will say Unconfigured Drive: and have single quoted # Vendor and Product strings displayed when its status is checked with mt. # # mt -f /dev/rmt/# status # Unconfigured Drive: Vendor 'VENDOR ' Product 'A Product ID ' # sense key(0x0)= No Additional Sense residual= 0 retries= 0 # file no= 0 block no= 0 # # If your drive is displayed like this first check to see if a newer version # of the st driver has added support for your drive. # # If your drive is not supported by Sun, check the drive manufacturer's # documentation or web site for their recommended configuration strings. # # To configure a drive not supported by the driver, use the single quoted # Vendor and Product strings to create a entry under tape-config-list. # # A starting point for your st.conf entry can be obtained by reading the # current DEFAULT configuration from the driver using mt. # # mt -f /dev/rmt/# config # "SONY SDX-700C", "SONY SDX-700C", "SONYSDX700C"; # SONYSDX700C = \ # 2,0x12,0,0x1865B,4,0x00,0x00,0x00,0x00,0,120,120,3600,3600,3600,3600,3600; # # # Notes: # Any spaces in the Vendor field must be kept so that it is 8 # characters long. Trailing spaces in the Product field can be removed. # # To add this configuration information, first uncomment the # "tape-config-list=" line, and add the first configuration line # immediately afterward. If there is more than one entry in the # tape-config-list, all entries but the last must end with a comma. # The last entry ends with a semicolon. # # See the driver.conf(5) man page for general information on the conf # file format, and the st(4D) man page for information specific to st.conf. # # Example: #tape-config-list= # "VENDOR A Product ID", "A Prettier Name to Display", "A-Config-Name", # "VENDORB Other Product ID", "An Other Pretty Name", "Other-Config-Name"; # # Then for each config-Name there must be a setup string that looks like this. # # A-Config-Name = \ # 2,0x34,0,0x18659,4,0x47,0x47,0x47,0x47,1,120,120,3600,3600,3600,3600,3600; # Other-Config-Name = 1,0x3B,0,0x18659,4,0x40,0x40,0x40,0x40,3; # # For specific details for of values to use see the st(4D) man pages and # drive vendor manuals. # name="st" class="scsi" target=0 lun=0; name="st" class="scsi" target=1 lun=0; name="st" class="scsi" target=2 lun=0; name="st" class="scsi" target=3 lun=0; name="st" class="scsi" target=4 lun=0; name="st" class="scsi" target=5 lun=0; name="st" class="scsi" target=6 lun=0; # # In case there are wide tape drives, one can use these targets # #name="st" class="scsi" target=8 lun=0; #name="st" class="scsi" target=9 lun=0; #name="st" class="scsi" target=10 lun=0; #name="st" class="scsi" target=11 lun=0; #name="st" class="scsi" target=12 lun=0; #name="st" class="scsi" target=13 lun=0; #name="st" class="scsi" target=14 lun=0; #name="st" class="scsi" target=15 lun=0;