xref: /illumos-gate/usr/src/cmd/bnu/Dialers (revision 7c478bd9)

#
# Copyright 2005 Sun Microsystems, Inc.  All rights reserved.
# Use is subject to license terms.
#
# CDDL HEADER START
#
# The contents of this file are subject to the terms of the
# Common Development and Distribution License, Version 1.0 only
# (the "License").  You may not use this file except in compliance
# with the License.
#
# You can obtain a copy of the license at usr/src/OPENSOLARIS.LICENSE
# or http://www.opensolaris.org/os/licensing.
# See the License for the specific language governing permissions
# and limitations under the License.
#
# When distributing Covered Code, include this CDDL HEADER in each
# file and include the License file at usr/src/OPENSOLARIS.LICENSE.
# If applicable, add the following below this CDDL HEADER, with the
# fields enclosed by brackets "[]" replaced with your own identifying
# information: Portions Copyright [yyyy] [name of copyright owner]
#
# CDDL HEADER END
#
#ident	"%Z%%M%	%I%	%E% SMI"
#
# Each caller type that appears in the Devices file (5th field)
# should appear in this file except for the built in callers.
# Each line consists of three parts:
# - the name of the caller
# - the translation table for the phone number to translate from
#   the 801 codes (=-) to the code for the particular device
# - a chat script (same format and meaning as the login scripts
#   that appear in the Systems file.
#
# Meaning of some of the escape characters:
# \p - pause (approximately 1/4-1/2 second delay)
# \d - delay (2 seconds)
# \D - phone number/token
# \T - phone number with Dialcodes and character translation
# \N - null byte
# \K - insert a BREAK
# \E - turn on echo checking (for slow devices)
# \e - turn off echo checking
# \r - carriage return
# \c - no new-line
# \n - send new-line
# \nnn - send octal number
#
# See the Administration Documentation for more details.
#
# NOTE: blank lines and lines that begin with a <space>, <tab>, or # are ignored

penril	=W-P	"" \d > Q\c : \d- > s\p9\c )-W\p\r\ds\p9\c-) y\c : \E\TP > 9\c OK
ventel	=&-%	"" \r\p\r\c $ <K\T%%\r>\c ONLINE!
vadic	=K-K	"" \005\p *-\005\p-*\005\p-* D\p BER? \E\T\e \r\c LINE
develcon ""	"" \pr\ps\c est:\007 \E\D\e \n\007
micom	""	"" \s\c NAME? \D\r\c GO
direct
##########
#	The following entry is for use with direct connections
#	using ttymon with the -b and -r options on both ends,
#	or the old uugetty with the -r option.
##########
uudirect ""	"" \r\d in:--in:

#  Rixon Intelligent Modem -- modem should be set up in the Rixon
#  mode and not the Hayes mode.
#
rixon	=&-%	"" \r\r\d $ s9\c )-W\r\ds9\c-) s\c : \T\r\c $ 9\c LINE

#   Hayes Smartmodem -- modem should be set with the configuration
#   switches as follows:
#
#       S1 - UP		S2 - UP		S3 - DOWN	S4 - UP
#       S5 - UP		S6 - DOWN	S7 - ?		S8 - DOWN
#
hayes	=,-,	"" \dA\pTE1V1X1Q0S2=255S12=255\r\c OK\r \EATDT\T\r\c CONNECT

#   USR Courier V.32 and Sportster
#   Set the switches as follows:
#
#   1 2 3 4 5 6 7 8 9 10
#   U U D U U U D D D U		Courier
#   U U D U U U U D		Sportster
#
usrv32-ec =,-,	"" \dA\pTE1V1X1Q0S2=255S12=255&A0&H1&M5&B2\r\c OK\r \EATDT\T\r\c CONNECT STTY=crtscts,crtsxoff
usrv32-nec =,-,	"" \dA\pTE1V1X1Q0S2=255S12=255&A0&H1&M0&B0\r\c OK\r \EATDT\T\r\c CONNECT STTY=crtscts,crtsxoff

#   Telebit TrailBlazer
#
tb1200	=W-,	"" \dA\pA\pA\pTE1V1X1Q0S2=255S12=255S50=2\r\c OK\r \EATDT\T\r\c CONNECT\s1200
tb2400	=W-,	"" \dA\pA\pA\pTE1V1X1Q0S2=255S12=255S50=3\r\c OK\r \EATDT\T\r\c CONNECT\s2400
tbfast	=W-,	"" \dA\pA\pA\pTE1V1X1Q0S2=255S12=255S50=255\r\c OK\r \EATDT\T\r\c CONNECT\sFAST

#   Telebit T1600
#
tb9600-ec =W-,	"" \dA\pA\pA\pTE1V1X1Q0S2=255S12=255S50=6\r\c OK\r \EATDT\T\r\c CONNECT\s9600 STTY=crtscts,crtsxoff
tb9600-nec =W-,	"" \dA\pA\pA\pTE1V1X1Q0S2=255S12=255S50=6S180=0\r\c OK\r \EATDT\T\r\c CONNECT\s9600 STTY=crtscts,crtsxoff

##########
#   AT&T Programmable 300/1200 Modem Model 4000
#
#	Commands:	Explanation:
#	------------	---------------------------------------------------
#	=,-,		Use comma for secondary dial tone & for pause
#	""		expect nothing
#	ATZ\r\p\p	enter command mode, reset modem,
#	OK\r		expect modem to reply OK
#	ATZ\r		enter command mode, reset modem
#	OK\r		expect modem to reply OK
#	\E		turn on echo check mode
#	ATDT\T\r\c	enter command mode, tone dial the number
#			(substitute 'P' for first 'T' for pulse dialing)
#	\T\r\c		phone number to dial
#	CONNECT		expect "CONNECT" from modem when connected
##########
att4000 =,-, ""  ATZ\r\p\p  OK\r ATZ\r OK\r\c \EATDT\T\r\c CONNECT

##########
#   AT&T Model 4024 Modem
#
#	For normal operation, dip switch 4 should be CLOSED.
#	This disables ENTER INTERACTIVE WITH <CR>.
#
#	Commands:	Explanation:
#	------------	---------------------------------------------------
#	=,-,		Use comma for secondary dial tone & for pause
#	""		expect nothing
#	atzod,		enter command mode, reset modem, set options to default
#	o12=y,		set option 12 to 'y' (transparent data mode)
#	o4=n\r\c	set option 4 to 'n' (don't disconnect on rcvd spaces)
#	\006		expect ACK from modem
#	atT\T\r\c	enter command mode, tone dial the number
#	ed		expect "ed" (actually "Answered")
#
#			Once transparent data mode is enabled, you
#			cannot enter the interactive mode from the data mode.
##########
att4024 =+-, "" atzod,o12=y,o4=n\r\c \006 atT\T\r\c ed

##########
#  AT&T DATAPHONE II 2212C Modem
#
#	For normal operation, dip switch 4 should be CLOSED.
#	This disables ENTER INTERACTIVE WITH <CR>.
#
#	Commands:	Explanation:
#	------------	---------------------------------------------------
#	=+-,		'+' for secondary dial tone, ',' for pause
#	""		expect nothing
#	atzod,		enter command mode, reset modem, set options to default
#	o12=y,		set option 12 to 'y' (transparent data mode)
#	o4=n,		set option 4 to 'n' (don't disconnect on rcvd spaces)
#	\006		Wait for ACK
#	atT\T\r\c	enter command mode, tone dial the number
#	ed		expect "ed" (actually "Answered")
#
#			Once transparent data mode is enabled, you
#			cannot enter the interactive mode from the data mode.
##########
att2212c =+-, "" atzod,o12=y,o4=n\r\c \006 atT\T\r\c ed
att2212C =+-, "" atzod,o12=y,o4=n\r\c \006 atT\T\r\c ed

##########
#  AT&T DATAPHONE II 2224B Modem
#
#	For normal operation dip switch S1 switch 2 should be OPEN.
#	This disables ENTER INTERACTIVE WITH <CR>.
#
#	Commands:	Explanation:
#	------------	---------------------------------------------------
#	=+-,		'+' for secondary dial tone, ',' for pause
#	""		expect nothing
#	atT\T\r\c	enter command mode, tone dial the number
#			(substitute 'P' for first 'T' for pulse dialing)
#	ed		expect "ed" (actually "Answered")
##########
att2224b =+-, "" atT\T\r\c ed
att2224B =+-, "" atT\T\r\c ed

##########
#  AT&T DATAPHONE II 2224CEO Modem
#
#	The 2224CEO Modem supports MNP error control protocol.
#	This entry will use MNP if it is also available on the
#	remote end.
#
#	For normal operation, dip switch S1 switch 3 should be UP.
#	This disables ENTER INTERACTIVE WITH <CR>.
#
#	When used with an EPORTS board on a 3B2, it is recommended that
#	hardware flow control be enabled on the board and that the
#	corresponding second set of entries below be used.
#	(i.e. change \\q0 to \\q3 below - use CTS/RTS flow control)
#
#	Commands:	Explanation:
#	------------	---------------------------------------------------
#	=+-,		'+' for secondary dial tone, ',' for pause
#	""		expect nothing
#	atzod,		enter command mode, reset options to default values,
#	o12=y,		set option 12 to 'y' (transparent data mode)
#	o4=n,		set option 4 to 'n' (don't disconnect on rcvd spaces)
#	\\n3		select normal operating mode
#	\\c1		modem does not buffer data
#	\\j0		do not autobaud modem serial port
#	\\q0		no flow control
#	\\g0\r\c	no modem port flow control
#	\006		Wait for ACK
#	atT\T\r\c	enter command mode, tone dial the number
#			(substitute 'P' for first 'T' for pulse dialing)
#	Connected	expect "ed" (actually "Connected")
#
#			Once transparent data mode is enabled, you
#			cannot enter the interactive mode from the data mode.
##########
att2224ceo =+-, "" atzod,o12=y,o4=n,\\n3\\c1\\j0\\q0\\g0\r\c \006 atT\T\r\c Connected
att2224CEO =+-, "" atzod,o12=y,o4=n,\\n3\\c1\\j0\\q0\\g0\r\c \006 atT\T\r\c Connected
#att2224ceo =+-, "" atzod,o12=y,o4=n,\\n3\\c1\\j0\\q3\\g0\r\c \006 atT\T\r\c Connected
#att2224CEO =+-, "" atzod,o12=y,o4=n,\\n3\\c1\\j0\\q3\\g0\r\c \006 atT\T\r\c Connected

##########
#  AT&T DATAPHONE II 2224G Modem
#
#	The 2224G Modem supports MNP error control protocol.
#	This entry will use MNP if it is also available on the
#	remote end.
#
#	For normal operation, dip switch S1 switch 3 should be RIGHT.
#	This disables ENTER INTERACTIVE WITH <CR>.
#
#	When used with an EPORTS board on a 3B2, it is recommended that
#	hardware flow control be enabled on the board and that the
#	corresponding second set of entries below be used.
#	(i.e. change \\q0 to \\q3 below - use CTS/RTS flow control)
#
#	Commands:	Explanation:
#	------------	---------------------------------------------------
#	=+-,		'+' for secondary dial tone, ',' for pause
#	""		expect nothing
#	atzod,		enter command mode, reset options to default values,
#	o12=y,		set option 12 to 'y' (transparent data mode)
#	o4=n,		set option 4 to 'n' (don't disconnect on rcvd spaces)
#	o1=n\r\c	set option 1 to 'n' (don't wait for far end sense first)
#	\006		Wait for ACK
#	atz		enter command mode
#	\\n3		select auto-reliable operating mode
#	\\c1		select auto-reliable buffering scheme 1
#	\\j0		do not autobaud modem serial port
#	\\q0		no flow control
#	\\g0\r\c	no modem port flow control
#	\datT\T\r\c	delay, enter command mode, tone dial the number
#			(substitute 'P' for first 'T' for pulse dialing)
#	Connected	expect "Connected"
#
#			Once transparent data mode is enabled, you
#			cannot enter the interactive mode from the data mode.
##########
att2224g =+-, "" atzod,o12=y,o4=n,o1=n\r\c \006 atz\\n3\\c1\\j0\\q0\\g0\r\c "" \datT\T\r\c Connected
att2224G =+-, "" atzod,o12=y,o4=n,o1=n\r\c \006 atz\\n3\\c1\\j0\\q0\\g0\r\c "" \datT\T\r\c Connected
#att2224g =+-, "" atzod,o12=y,o4=n,o1=n\r\c \006 atz\\n3\\c1\\j0\\q3\\g0\r\c "" \datT\T\r\c Connected
#att2224G =+-, "" atzod,o12=y,o4=n,o1=n\r\c \006 atz\\n3\\c1\\j0\\q3\\g0\r\c "" \datT\T\r\c Connected

##########
#  AT&T DATAPHONE II 2224 Modem
#
#	This entry is for 2224 with the optional automatic caller.
#	Is is provided only to provide compatibility with previous
#	releases. The entry for the specific model modem you own
#	should be found above.
#
#	Commands:	Explanation:
#	------------	---------------------------------------------------
#	=+-,		'+' for secondary dial tone, ',' for pause
#	""		expect nothing
#	\r\c		send carriage return to enter interactive mode
#	:--:		expect colon.  if don't see it, send newline
#			and expect colon again.
#	T\T\r\c		dial the given number, using touch-tone signaling
#			(change the first T to P if you want to use pulse
#			dialing).
#	red		expect "red" (actually "Answered")
##########
att2224	=+-,	"" \r\c :--: T\T\r\c red

##########
#  AT&T DATAPHONE II 2248A Modem
#
#	Commands:	Explanation:
#	------------	---------------------------------------------------
#	=+-,		'+' for secondary dial tone, ',' for pause
#	""		expect nothing
#	atzod,		enter command mode, reset modem, set options to default
#	o12=y\r\c	set option 12 to 'y' (transparent data mode)
#	\006		Wait for ACK
#	atT\T\r\c	enter command mode, tone dial the number
#			(substitute 'P' for first 'T' for pulse dialing)
#	Connected	expect "Connected"
#
##########
att2248a =+-, "" atzod,o12=y\r\c \006 atT\T\r\c Connected
att2248A =+-, "" atzod,o12=y\r\c \006 atT\T\r\c Connected

##########
#  AT&T DATAPHONE II 2296A Modem
#
#	Commands:	Explanation:
#	------------	---------------------------------------------------
#	=+-,		'+' for secondary dial tone, ',' for pause
#	""		expect nothing
#	atzod,		enter command mode, reset options to default values,
#	o12=y,		set option 12 to 'y' (transparent data mode)
#	o50=y,		set option 50 to 'y'
#	o51=n,		set option 51 to 'n' (don't strap CTS/RTS)
#	o55=n,		set option 55 to 'n' (CD does not indicate carrier)
#	o69=n,\r\c	set option 69 to 'n'
#	\006		Wait for ACK
#	atz		enter command mode
#	\\n3		select auto-reliable operating mode
#	\\c1		select auto-reliable buffering scheme 1
#	\\j0		do not autobaud modem serial port
#	\\q0		no flow control
#	\\g0\r\c	no modem port flow control
#	\datT\T\r\c	delay, enter command mode, tone dial the number
#			(substitute 'P' for first 'T' for pulse dialing)
#	Connected	expect "Connected"
#
#	When used with an EPORTS board on a 3B2, it is recommended that
#	hardware flow control be enabled on the board and that the
#	corresponding second set of entries below be used.
#	(i.e. change \\q0 to \\q3 below - use CTS/RTS flow control)
#
##########
att2296a =+-, "" atzod,o12=y,o50=y,o51=n,o55=n,o69=n\r\c \006 atz\\n3\\c1\\j0\\q0\\g0\r\c "" \datT\T\r\c Connected
att2296A =+-, "" atzod,o12=y,o50=y,o51=n,o55=n,o69=n\r\c \006 atz\\n3\\c1\\j0\\q0\\g0\r\c "" \datT\T\r\c Connected
#att2296a =+-, "" atzod,o12=y,o50=y,o51=n,o55=n,o69=n\r\c \006 atz\\n3\\c1\\j0\\q0\\g0\r\c "" \datT\T\r\c Connected
#att2296A =+-, "" atzod,o12=y,o50=y,o51=n,o55=n,o69=n\r\c \006 atz\\n3\\c1\\j0\\q0\\g0\r\c "" \datT\T\r\c Connected

##########
#  Network Listener Service
#  The format of the request to the listener is
#		NLPS:000:001:<service_code>\N\c
#  where <service_code> determines what server the listener invokes.
#  The entry below asks for service code 1.
#
#  If cu & uucico use different service codes, you will have to use
#  separate Dialers files (e.g., Dialers.cico and Dialers.cu).
#  See comments in Sysfiles for instructions.
##########
nls	""	"" NLPS:000:001:1\N\c

##########
# DATAKIT(r) serial port connection script
#
#	Commands:	Explanation:
#	------------	---------------------------------------------------
#	""		no special character translation table
#	""		expect nothing
#	\d		delay to give some settling time
#	TION:--TION:	wait for the DESTINATION: prompt, if it does not come
#			send a carriage return and wait again.
#	\D		send the specified token
##########
datakit	""	"" \d TION:--TION: \D