/* * CDDL HEADER START * * The contents of this file are subject to the terms of the * Common Development and Distribution License (the "License"). * You may not use this file except in compliance with the License. * * You can obtain a copy of the license at usr/src/OPENSOLARIS.LICENSE * or http://www.opensolaris.org/os/licensing. * See the License for the specific language governing permissions * and limitations under the License. * * When distributing Covered Code, include this CDDL HEADER in each * file and include the License file at usr/src/OPENSOLARIS.LICENSE. * If applicable, add the following below this CDDL HEADER, with the * fields enclosed by brackets "[]" replaced with your own identifying * information: Portions Copyright [yyyy] [name of copyright owner] * * CDDL HEADER END */ /* * Copyright (c) 2007, 2010, Oracle and/or its affiliates. All rights reserved. * Copyright (c) 2018, Joyent, Inc. All rights reserved. */ #ifndef _LIBIPMI_H #define _LIBIPMI_H #include #include #include /* * Private interfaces for communicating with attached services over IPMI. This * library is designed for system software communicating with Illumos-supported * service processors over /dev/ipmi0. It is not a generic IPMI library. * * Documentation references refer to "Intelligent Platform Management Interface * Specification Second Generation v2.0", document revision 1.0 with Februrary * 15, 2006 Markup from "IPMI v2.0 Addenda, Errata, and Clarifications Revision * 3". */ #ifdef __cplusplus extern "C" { #endif typedef struct ipmi_handle ipmi_handle_t; #pragma pack(1) /* * Basic netfn definitions. See section 5.1. */ #define IPMI_NETFN_CHASSIS 0x0 #define IPMI_NETFN_BRIDGE 0x2 #define IPMI_NETFN_SE 0x4 #define IPMI_NETFN_APP 0x6 #define IPMI_NETFN_FIRMWARE 0x8 #define IPMI_NETFN_STORAGE 0xa #define IPMI_NETFN_TRANSPORT 0x0C #define IPMI_NETFN_OEM 0x2e /* * Error definitions */ #define EIPMI_BASE 2000 typedef enum { EIPMI_NOMEM = EIPMI_BASE, /* memory allocation failure */ EIPMI_BMC_OPEN_FAILED, /* failed to open /dev/ipmi0 */ EIPMI_BMC_PUTMSG, /* failed to send message to /dev/ipmi0 */ EIPMI_BMC_GETMSG, /* failed to read response from /dev/ipmi0 */ EIPMI_BMC_RESPONSE, /* response from /dev/ipmi0 failed */ EIPMI_INVALID_COMMAND, /* invalid command */ EIPMI_COMMAND_TIMEOUT, /* command timeout */ EIPMI_DATA_LENGTH_EXCEEDED, /* maximum data length exceeded */ EIPMI_SEND_FAILED, /* failed to send BMC request */ EIPMI_UNSPECIFIED, /* unspecified BMC error */ EIPMI_UNKNOWN, /* unknown error */ EIPMI_BAD_RESPONSE, /* received unexpected response */ EIPMI_BAD_RESPONSE_LENGTH, /* unexpected response length */ EIPMI_INVALID_RESERVATION, /* invalid or cancelled reservation */ EIPMI_NOT_PRESENT, /* requested entity not present */ EIPMI_INVALID_REQUEST, /* malformed request data */ EIPMI_BUSY, /* service processor is busy */ EIPMI_NOSPACE, /* service processor is out of space */ EIPMI_UNAVAILABLE, /* service processor is unavailable */ EIPMI_ACCESS, /* insufficient privileges */ EIPMI_BADPARAM, /* parameter is not supported */ EIPMI_READONLY, /* attempt to write read-only param */ EIPMI_WRITEONLY, /* attempt to read write-only param */ EIPMI_LAN_OPEN_FAILED, /* failed to open socket */ EIPMI_LAN_PING_FAILED, /* RMCP Ping message failed */ EIPMI_LAN_PASSWD_NOTSUP, /* password authentication not supported */ EIPMI_LAN_CHALLENGE, /* failure getting challenge */ EIPMI_LAN_SESSION, /* failure activating session */ EIPMI_LAN_SETPRIV /* failure setting session privs */ } ipmi_errno_t; /* * Basic library functions. * * The ipmi_handle is the primary interface to the library. The library itself * is not MT-safe, but it is safe within a single handle. Multithreaded clients * should either open multiple handles, or otherwise synchronize access to the * same handle. * * There is a single command response buffer that is stored with the handle, to * simplify memory management in the caller. The memory referenced by a command * response is only valid until the next command is issued. The caller is * responsible for making a copy of the response if it is needed. */ extern ipmi_handle_t *ipmi_open(int *, char **, uint_t xport_type, nvlist_t *); /* * Constants for nvpair names for the params nvlist that is passed to * ipmi_open(). If the IPMI_TRANSPORT_BMC is desired, then it is sufficient * to just specify NULL for the params nvlist. * * For IPMI_TRANSPORT_LAN, the params nvlist must contain the following * nvpairs: * * IPMI_LAN_HOST, IPMI_LAN_USER, IPMI_LAN_PASSWD * * IPMI_LAN_PORT is optional and will default to 623 * IPMI_LAN_PRIVLVL is optional and will default to admin * IPMI_LAN_TIMEOUT is optional and will default to 3 seconds * IPMI_LAN_NUM_RETIES is optional and will default to 5 */ #define IPMI_TRANSPORT_TYPE "transport-type" #define IPMI_TRANSPORT_BMC 0x01 #define IPMI_TRANSPORT_LAN 0x02 #define IPMI_LAN_HOST "lan-host" #define IPMI_LAN_PORT "lan-port" #define IPMI_LAN_USER "lan-user" #define IPMI_LAN_PASSWD "lan-passwd" #define IPMI_LAN_PRIVLVL "lan-privlvl" #define IPMI_LAN_TIMEOUT "lan-timeout" #define IPMI_LAN_NUM_RETRIES "lan-num-retries" extern void ipmi_close(ipmi_handle_t *); extern int ipmi_errno(ipmi_handle_t *); extern const char *ipmi_errmsg(ipmi_handle_t *); /* * Raw requests. See section 5. */ typedef struct ipmi_cmd { uint8_t ic_netfn:6; uint8_t ic_lun:2; uint8_t ic_cmd; uint16_t ic_dlen; void *ic_data; } ipmi_cmd_t; extern ipmi_cmd_t *ipmi_send(ipmi_handle_t *, ipmi_cmd_t *); /* * Retrieve basic information about the IPMI device. See section 20.1 "Get * Device ID Command". */ #define IPMI_CMD_GET_DEVICEID 0x01 typedef struct ipmi_deviceid { uint8_t id_devid; DECL_BITFIELD3( id_dev_rev :4, __reserved :3, id_dev_sdrs :1); DECL_BITFIELD2( id_firm_major :7, id_dev_available :1); uint8_t id_firm_minor; uint8_t id_ipmi_rev; uint8_t id_dev_support; uint8_t id_manufacturer[3]; uint8_t id_product[2]; } ipmi_deviceid_t; #define IPMI_OEM_SUN 0x2a #define IPMI_PROD_SUN_ILOM 0x4701 ipmi_deviceid_t *ipmi_get_deviceid(ipmi_handle_t *); #define ipmi_devid_manufacturer(dp) \ ((dp)->id_manufacturer[0] | \ ((dp)->id_manufacturer[1] << 8) | \ ((dp)->id_manufacturer[2] << 16)) #define ipmi_devid_product(dp) \ ((dp)->id_product[0] | \ ((dp)->id_product[1] << 8)) const char *ipmi_firmware_version(ipmi_handle_t *); /* * Get Channel Auth Caps. See section 22.13. */ typedef struct ipmi_channel_auth_caps { uint8_t cap_channel; DECL_BITFIELD3( cap_authtype :6, __reserved1 :1, cap_ipmirev2 :1); DECL_BITFIELD5( cap_anon :3, cap_peruser :1, cap_permesg :1, cap_kgstatus :1, __reserved2 :2); uint8_t cap_ext; uint8_t cap_oemid[3]; uint8_t cap_oemaux; } ipmi_channel_auth_caps_t; #define IPMI_CMD_GET_CHANNEL_AUTH_CAPS 0x38 extern ipmi_channel_auth_caps_t *ipmi_get_channel_auth_caps(ipmi_handle_t *, uint8_t, uint8_t); /* * Get Channel Info. See section 22.24. */ typedef struct ipmi_channel_info { DECL_BITFIELD2( ici_number :4, __reserved1 :4); DECL_BITFIELD2( ici_medium :7, __reserved2 :1); DECL_BITFIELD2( ici_protocol :5, __reserved3 :3); DECL_BITFIELD3( ici_session_count :6, ici_single_session :1, ici_multi_Session :1); uint8_t ici_vendor[3]; uint8_t ici_auxinfo[2]; } ipmi_channel_info_t; #define IPMI_CMD_GET_CHANNEL_INFO 0x42 /* * Channel Numbers. See section 6.3. */ #define IPMI_CHANNEL_PRIMARY 0x0 #define IPMI_CHANNEL_MIN 0x1 #define IPMI_CHANNEL_MAX 0xB #define IPMI_CHANNEL_CURRENT 0xE #define IPMI_CHANNEL_SYSTEM 0xF extern ipmi_channel_info_t *ipmi_get_channel_info(ipmi_handle_t *, int); /* * Channel Protocol Types. See section 6.4. */ #define IPMI_PROTOCOL_IPMB 0x1 #define IPMI_PROTOCOL_ICMB 0x2 #define IPMI_PROTOCOL_SMBUS 0x4 #define IPMI_PROTOCOL_KCS 0x5 #define IPMI_PROTOCOL_SMIC 0x6 #define IPMI_PROTOCOL_BT10 0x7 #define IPMI_PROTOCOL_BT15 0x8 #define IPMI_PROTOCOL_TMODE 0x9 #define IPMI_PROTOCOL_OEM1 0xC #define IPMI_PROTOCOL_OEM2 0xD #define IPMI_PROTOCOL_OEM3 0xE #define IPMI_PROTOCOL_OEM4 0xF /* * Channel Medium Types. See section 6.5. */ #define IPMI_MEDIUM_IPMB 0x1 #define IPMI_MEDIUM_ICMB10 0x2 #define IPMI_MEDIUM_ICMB09 0x3 #define IPMI_MEDIUM_8023LAN 0x4 #define IPMI_MEDIUM_RS232 0x5 #define IPMI_MEDIUM_OTHERLAN 0x6 #define IPMI_MEDIUM_PCISMBUS 0x7 #define IPMI_MEDIUM_SMBUS10 0x8 #define IPMI_MEDIUM_SMBUS20 0x9 #define IPMI_MEDIUM_USB1 0xA #define IPMI_MEDIUM_USB2 0xB #define IPMI_MEDIUM_SYSTEM 0xC /* * LAN Configuration. See section 23. While the underlying mechanism is * implemented via a sequence of get/set parameter commands, we assume that * consumers prefer to get and set information in chunks, and therefore expose * the configuration as a structure, with some of the less useful fields * removed. When making changes, the consumer specifies which fields to apply * along with the structure the library takes care of the rest of the work. * * This can be expanded in the future as needed. */ typedef struct ipmi_lan_config { boolean_t ilc_set_in_progress; uint32_t ilc_ipaddr; uint8_t ilc_ipaddr_source; uint8_t ilc_macaddr[6]; uint32_t ilc_subnet; uint32_t ilc_gateway_addr; } ipmi_lan_config_t; #define IPMI_LAN_SRC_UNSPECIFIED 0x0 #define IPMI_LAN_SRC_STATIC 0x1 #define IPMI_LAN_SRC_DHCP 0x2 #define IPMI_LAN_SRC_BIOS 0x3 #define IPMI_LAN_SRC_OTHER 0x4 #define IPMI_LAN_SET_IPADDR 0x01 #define IPMI_LAN_SET_IPADDR_SOURCE 0x02 #define IPMI_LAN_SET_MACADDR 0x04 #define IPMI_LAN_SET_SUBNET 0x08 #define IPMI_LAN_SET_GATEWAY_ADDR 0x10 #define IPMI_CMD_SET_LAN_CONFIG 0x01 #define IPMI_CMD_GET_LAN_CONFIG 0x02 extern int ipmi_lan_get_config(ipmi_handle_t *, int, ipmi_lan_config_t *); extern int ipmi_lan_set_config(ipmi_handle_t *, int, ipmi_lan_config_t *, int); /* * SEL (System Event Log) commands. Currently the library only provides * commands for reading the SEL. */ /* * 31.2 Get SEL Info Command */ #define IPMI_CMD_GET_SEL_INFO 0x40 typedef struct ipmi_sel_info { uint8_t isel_version; uint16_t isel_entries; uint16_t isel_free; uint32_t isel_add_ts; uint32_t isel_erase_ts; DECL_BITFIELD6( isel_supp_allocation :1, isel_supp_reserve :1, isel_supp_partial :1, isel_supp_delete :1, __reserved :3, isel_overflow :1); } ipmi_sel_info_t; extern ipmi_sel_info_t *ipmi_sel_get_info(ipmi_handle_t *); extern boolean_t ipmi_sdr_changed(ipmi_handle_t *); extern int ipmi_sdr_refresh(ipmi_handle_t *); /* * 32.1 SEL Event Records */ typedef struct ipmi_sel_event { uint16_t isel_ev_next; uint16_t isel_ev_recid; uint8_t isel_ev_rectype; uint32_t isel_ev_ts; DECL_BITFIELD2( isel_ev_software :1, isel_ev_addr_or_id :7); DECL_BITFIELD3( isel_ev_lun :2, __reserved :2, isel_ev_channel :4); uint8_t isel_ev_rev; uint8_t isel_ev_sensor_type; uint8_t isel_ev_sensor_number; DECL_BITFIELD2( isel_ev_type :7, isel_ev_dir :1); uint8_t isel_ev_data[3]; } ipmi_sel_event_t; #define IPMI_EV_REV15 0x04 #define IPMI_EV_REV1 0x03 #define IPMI_SEL_SYSTEM 0x02 #define IPMI_SEL_OEMTS_LO 0xC0 #define IPMI_SEL_OEMTS_HI 0xDF #define IPMI_SEL_OEM_LO 0xE0 #define IPMI_SEL_OEM_HI 0xFF #define IPMI_EV_ASSERT 0x0 #define IPMI_EV_DEASSERT 0x1 /* * 32.2 OEM SEL Record (with timestamp) */ typedef struct ipmi_sel_oem_ts { uint16_t isel_oem_next; uint16_t isel_oem_id; uint8_t isel_oem_type; uint32_t isel_oem_ts; uint8_t isel_oem_devid[3]; uint8_t isel_oem_data[6]; } ipmi_sel_oem_ts_t; /* * 32.3 OEM SEL Record (no timestamp) */ typedef struct ipmi_sel_oem { uint16_t isel_oem_next; uint16_t isel_oem_id; uint8_t isel_oem_type; uint8_t isel_oem_data[13]; } ipmi_sel_oem_t; /* * 29.3 Platform Event Message Command. */ typedef struct ipmi_platform_event_message { uint8_t ipem_generator; uint8_t ipem_rev; uint8_t ipem_sensor_type; uint8_t ipem_sensor_num; DECL_BITFIELD2( ipem_event_type :7, ipem_event_dir :1); uint8_t ipem_event_data[3]; } ipmi_platform_event_message_t; #define IPMI_CMD_PLATFORM_EVENT_MESSAGE 0x02 extern int ipmi_event_platform_message(ipmi_handle_t *, ipmi_platform_event_message_t *); /* * 29.7 Event Data Field Formats. Consumers can cast the data field of the * event record to the appropriate type depending on the sensor class. */ typedef struct ipmi_event_threshold { DECL_BITFIELD3( iev_offset :4, iev_desc_byte3 :2, iev_desc_byte2 :2); uint8_t iev_reading; uint8_t iev_threshold; } ipmi_event_threshold_t; #define IPMI_EV_DESC_UNSPECIFIED 0x00 #define IPMI_EV_DESC_TRIGGER 0x01 #define IPMI_EV_DESC_OEM 0x02 #define IPMI_EV_DESC_SPECIFIC 0x03 typedef struct ipmi_event_discrete { DECL_BITFIELD3( iev_offset :4, iev_desc_byte3 :2, iev_desc_byte2 :2); DECL_BITFIELD2( iev_offset_type :4, iev_offset_severity :4); uint8_t iev_oem_code; } ipmi_event_discrete_t; #define IPMI_EV_DESC_PREVSTATE 0x01 #define IPMI_EV_DESC_SPECIFIC 0x03 typedef struct ipmi_event_oem { DECL_BITFIELD3( iev_offset :4, iev_desc_byte3 :2, iev_desc_byte2 :2); DECL_BITFIELD2( iev_offset_type :4, iev_offset_severity :4); uint8_t iev_oem_code; } ipmi_event_oem_t; /* * Get SEL Entry Command. See section 31.5. We don't support partial reads, so * this interface is quite a bit simpler than in the spec. We default to * returning event records, though the consumer should check the type field and * cast it to the appropriate type if it is no IPMI_SEL_SYSTEM. */ #define IPMI_CMD_GET_SEL_ENTRY 0x43 extern ipmi_sel_event_t *ipmi_sel_get_entry(ipmi_handle_t *, uint16_t); #define IPMI_SEL_FIRST_ENTRY 0x0000 #define IPMI_SEL_LAST_ENTRY 0xFFFF /* * SEL time management. See sections 31.10 and 31.11. */ #define IPMI_CMD_GET_SEL_TIME 0x48 #define IPMI_CMD_SET_SEL_TIME 0x49 #define IPMI_CMD_GET_SEL_UTC_OFFSET 0x5C #define IPMI_CMD_SET_SEL_UTC_OFFSET 0x5D extern int ipmi_sel_get_time(ipmi_handle_t *, uint32_t *); extern int ipmi_sel_set_time(ipmi_handle_t *, uint32_t); extern int ipmi_sel_get_utc_offset(ipmi_handle_t *, int *); extern int ipmi_sel_set_utc_offset(ipmi_handle_t *, int); /* * SDR (Sensor Device Record) requests. A cache of the current SDR repository * is kept as part of the IPMI handle and updated when necessary. This does the * work of processing the SDR names and providing an easy way to lookup * individual records and iterate over all records. */ /* * Get SDR Repository Info Command. See section 33.9. */ #define IPMI_CMD_GET_SDR_INFO 0x20 typedef struct ipmi_sdr_info { uint8_t isi_version; uint16_t isi_record_count; uint16_t isi_free_space; uint32_t isi_add_ts; uint32_t isi_erase_ts; DECL_BITFIELD7( isi_supp_allocation :1, isi_supp_reserve :1, isi_supp_partial :1, isi_supp_delete :1, __reserved :1, isi_modal :2, isi_overflow :1); } ipmi_sdr_info_t; extern ipmi_sdr_info_t *ipmi_sdr_get_info(ipmi_handle_t *); /* * Reserve repository command. See section 33.11. */ #define IPMI_CMD_RESERVE_SDR_REPOSITORY 0x22 /* * Get SDR command. See section 33.12. This command accesses the raw SDR * repository. Clients can also use the lookup functions to retrieve a * particular SDR record by name. * * The list of possible types is indicated in the sub-chapters of section 43. */ typedef struct ipmi_sdr { uint16_t is_id; uint8_t is_version; uint8_t is_type; uint8_t is_length; uint8_t is_record[1]; } ipmi_sdr_t; #define IPMI_CMD_GET_SDR 0x23 #define IPMI_SDR_FIRST 0x0000 #define IPMI_SDR_LAST 0xFFFF extern ipmi_sdr_t *ipmi_sdr_get(ipmi_handle_t *, uint16_t, uint16_t *); /* * Full Sensor Record. See 43.1 */ #define IPMI_SDR_TYPE_FULL_SENSOR 0x01 typedef struct ipmi_sdr_full_sensor { /* RECORD KEY BYTES */ uint8_t is_fs_owner; DECL_BITFIELD3( is_fs_sensor_lun :2, __reserved1 :2, is_fs_channel :4); uint8_t is_fs_number; /* RECORD BODY BYTES */ uint8_t is_fs_entity_id; DECL_BITFIELD2( is_fs_entity_instance :7, is_fs_entity_logical :1); DECL_BITFIELD8( is_fs_sensor_scanning_enabled :1, is_fs_event_generation_enabled :1, is_fs_init_sensor_type :1, is_fs_init_hysteresis :1, is_fs_init_thresholds :1, is_fs_init_events :1, is_fs_init_scanning :1, is_fs_settable :1); DECL_BITFIELD5( is_fs_event_support :2, is_fs_threshold_support :2, is_fs_hysteresis_support :2, is_fs_rearm_support :1, is_fs_ignore :1); uint8_t is_fs_type; uint8_t is_fs_reading_type; uint16_t is_fs_assert_mask; uint16_t is_fs_deassert_mask; uint16_t is_fs_reading_mask; DECL_BITFIELD4( is_fs_units_isprcnt :1, is_fs_mod_unit :2, is_fs_rate_unit :3, is_fs_analog_fmt :2); uint8_t is_fs_unit2; uint8_t is_fs_unit3; /* Linearization */ DECL_BITFIELD2( is_fs_sensor_linear_type :7, __reserved2 :1); /* M, Tolerance */ uint16_t is_fs_mtol; /* B, Accuracy, R exp, B exp */ uint32_t is_fs_bacc; DECL_BITFIELD4( is_fs_nominal_reading_spec :1, is_fs_normal_max_spec :1, is_fs_normal_min_spec :1, __reserved3 :5); uint8_t is_fs_nominal_reading; uint8_t is_fs_normal_maximum; uint8_t is_fs_normal_minimum; uint8_t is_fs_max; uint8_t is_fs_min; uint8_t is_fs_upper_nonrecov; uint8_t is_fs_upper_critical; uint8_t is_fs_upper_noncrit; uint8_t is_fs_lower_nonrecov; uint8_t is_fs_lower_critical; uint8_t is_fs_lower_noncrit; uint8_t is_fs_hysteresis_positive; uint8_t is_fs_hysteresis_negative; uint16_t __reserved4; uint8_t is_fs_oem; DECL_BITFIELD3( is_fs_idlen :5, __reserved5 :1, is_fs_idtype :2); char is_fs_idstring[1]; } ipmi_sdr_full_sensor_t; #define IPMI_SDR_TYPE_COMPACT_SENSOR 0x02 /* * Compact Sensor Record. See section 43.2 */ typedef struct ipmi_sdr_compact_sensor { /* RECORD KEY BYTES */ uint8_t is_cs_owner; DECL_BITFIELD3( is_cs_sensor_lun :2, is_cs_fru_lun :2, is_cs_channel :4); uint8_t is_cs_number; /* RECORD BODY BYTES */ uint8_t is_cs_entity_id; DECL_BITFIELD2( is_cs_entity_instance :7, is_cs_entity_logical :1); DECL_BITFIELD8( is_cs_sensor_scanning_enabled :1, is_cs_event_generation_enabled :1, is_cs_init_sensor_type :1, is_cs_init_hysteresis :1, __reserved1 :1, is_cs_init_events :1, is_cs_init_scanning :1, is_cs_settable :1); DECL_BITFIELD5( is_cs_event_support :2, is_cs_threshold_support :2, is_cs_hysteresis_support :2, is_cs_rearm_support :1, is_cs_ignore :1); uint8_t is_cs_type; uint8_t is_cs_reading_type; uint16_t is_cs_assert_mask; uint16_t is_cs_deassert_mask; uint16_t is_cs_reading_mask; DECL_BITFIELD4( is_cs_units_isprcnt :1, is_cs_mod_unit :2, is_cs_rate_unit :3, __reserved2 :2); uint8_t is_cs_unit2; uint8_t is_cs_unit3; DECL_BITFIELD3( is_cs_share_count :4, is_cs_modifier_type :2, is_cs_direction :2); DECL_BITFIELD2( is_cs_modifier_offset :7, is_cs_sharing :1); uint8_t is_cs_hysteresis_positive; uint8_t is_cs_hysteresis_negative; uint16_t __reserved3; uint8_t __reserved4; uint8_t is_cs_oem; DECL_BITFIELD3( is_cs_idlen :5, __reserved5 :1, is_cs_idtype :2); char is_cs_idstring[1]; } ipmi_sdr_compact_sensor_t; /* * Threshold sensor masks for is_cs_assert_mask and is_cs_deassert_mask. */ #define IPMI_SENSOR_RETURN_NONRECOV 0x4000 #define IPMI_SENSOR_RETURN_CRIT 0x2000 #define IPMI_SENSOR_RETURN_NONCRIT 0x1000 #define IPMI_SENSOR_MASK_UPPER_NONRECOV_HI 0x0800 #define IPMI_SENSOR_MASK_UPPER_NONRECOV_LO 0x0400 #define IPMI_SENSOR_MASK_UPPER_CRIT_HI 0x0200 #define IPMI_SENSOR_MASK_UPPER_CRIT_LO 0x0100 #define IPMI_SENSOR_MASK_UPPER_NONCRIT_HI 0x0080 #define IPMI_SENSOR_MASK_UPPER_NONCRIT_LO 0x0040 #define IPMI_SENSOR_MASK_LOWER_NONRECOV_HI 0x0020 #define IPMI_SENSOR_MASK_LOWER_NONRECOV_LO 0x0010 #define IPMI_SENSOR_MASK_LOWER_CRIT_HI 0x0008 #define IPMI_SENSOR_MASK_LOWER_CRIT_LO 0x0004 #define IPMI_SENSOR_MASK_LOWER_NONCRIT_HI 0x0002 #define IPMI_SENSOR_MASK_LOWER_NONCRIT_LO 0x0001 /* * Threshold sensor masks for is_cs_reading_mask. */ #define IPMI_SENSOR_SETTABLE_UPPER_NONRECOV 0x2000 #define IPMI_SENSOR_SETTABLE_UPPER_CRIT 0x1000 #define IPMI_SENSOR_SETTABLE_UPPER_NONCRIT 0x0800 #define IPMI_SENSOR_SETTABLE_LOWER_NONRECOV 0x0400 #define IPMI_SENSOR_SETTABLE_LOWER_CRIT 0x0200 #define IPMI_SENSOR_SETTABLE_LOWER_NONCRIT 0x0100 #define IPMI_SENSOR_READABLE_UPPER_NONRECOV 0x0020 #define IPMI_SENSOR_READABLE_UPPER_CRIT 0x0010 #define IPMI_SENSOR_READABLE_UPPER_NONCRIT 0x0008 #define IPMI_SENSOR_READABLE_LOWER_NONRECOV 0x0004 #define IPMI_SENSOR_READABLE_LOWER_CRIT 0x0002 #define IPMI_SENSOR_READABLE_LOWER_NONCRIT 0x0001 /* * Values for is_cs_reading_type. See table 42-2. */ #define IPMI_RT_THRESHOLD 0x01 #define IPMI_RT_USAGE 0x02 #define IPMI_RT_STATE 0x03 #define IPMI_RT_PREDFAIL 0x04 #define IPMI_RT_LIMIT 0x05 #define IPMI_RT_PERFORMANCE 0x06 #define IPMI_RT_SEVERITY 0x07 #define IPMI_RT_PRESENT 0x08 #define IPMI_RT_ENABLED 0x09 #define IPMI_RT_AVAILABILITY 0x0A #define IPMI_RT_REDUNDANCY 0x0B #define IPMI_RT_ACPI 0x0C #define IPMI_RT_SPECIFIC 0x6F /* * Bitmasks based on above reading types. See table 42-2 */ #define IPMI_SR_THRESHOLD_LOWER_NONCRIT_LOW 0x0001 #define IPMI_SR_THRESHOLD_LOWER_NONCRIT_HIGH 0x0002 #define IPMI_SR_THRESHOLD_LOWER_CRIT_LOW 0x0004 #define IPMI_SR_THRESHOLD_LOWER_CRIT_HIGH 0x0008 #define IPMI_SR_THRESHOLD_LOWER_NONRECOV_LOW 0x0010 #define IPMI_SR_THRESHOLD_LOWER_NONRECOV_HIGH 0x0020 #define IPMI_SR_THRESHOLD_UPPER_NONCRIT_LOW 0x0040 #define IPMI_SR_THRESHOLD_UPPER_NONCRIT_HIGH 0x0080 #define IPMI_SR_THRESHOLD_UPPER_CRIT_LOW 0x0100 #define IPMI_SR_THRESHOLD_UPPER_CRIT_HIGH 0x0200 #define IPMI_SR_THRESHOLD_UPPER_NONRECOV_LOW 0x0400 #define IPMI_SR_THRESHOLD_UPPER_NONRECOV_HIGH 0x0800 #define IPMI_SR_USAGE_IDLE 0x0001 #define IPMI_SR_USAGE_ACTIVE 0x0002 #define IPMI_SR_USAGE_BUSY 0x0004 #define IPMI_SR_STATE_DEASSERT 0x0001 #define IPMI_SR_STATE_ASSERT 0x0002 #define IPMI_SR_PREDFAIL_DEASSERT 0x0001 #define IPMI_SR_PREDFAIL_ASSERT 0x0002 #define IPMI_SR_LIMIT_NOTEXCEEDED 0x0001 #define IPMI_SR_LIMIT_EXCEEDED 0x0002 #define IPMI_SR_PERFORMANCE_MET 0x0001 #define IPMI_SR_PERFORMANCE_LAGS 0x0002 #define IPMI_SR_SEVERITY_TO_OK 0x0001 #define IPMI_SR_SEVERITY_OK_TO_NONCRIT 0x0002 #define IPMI_SR_SEVERITY_LESS_TO_CRIT 0x0004 #define IPMI_SR_SEVERITY_LESS_TO_NONRECOV 0x0008 #define IPMI_SR_SEVERITY_MORE_TO_NONCRIT 0x0010 #define IPMI_SR_SEVERITY_NONRECOV_TO_CRIT 0x0020 #define IPMI_SR_SEVERITY_TO_NONRECOV 0x0040 #define IPMI_SR_SEVERITY_MONITOR 0x0080 #define IPMI_SR_SEVERITY_INFO 0x0100 #define IPMI_SR_PRESENT_DEASSERT 0x0001 #define IPMI_SR_PRESENT_ASSERT 0x0002 #define IPMI_SR_ENABLED_DEASSERT 0x0001 #define IPMI_SR_ENABLED_ASSERT 0x0002 #define IPMI_SR_AVAILABILITY_RUNNING 0x0001 #define IPMI_SR_AVAILABILITY_INTEST 0x0002 #define IPMI_SR_AVAILABILITY_POWEROFF 0x0004 #define IPMI_SR_AVAILABILITY_ONLINE 0x0008 #define IPMI_SR_AVAILABILITY_OFFLINE 0x0010 #define IPMI_SR_AVAILABILITY_OFFDUTY 0x0020 #define IPMI_SR_AVAILABILITY_DEGRADED 0x0040 #define IPMI_SR_AVAILABILITY_POWERSAVE 0x0080 #define IPMI_SR_AVAILABILITY_INSTALLERR 0x0100 #define IPMI_SR_REDUNDANCY_FULL 0x0001 #define IPMI_SR_REDUNDANCY_LOST 0x0002 #define IPMI_SR_REDUNDANCY_DEGRADED 0x0004 #define IPMI_SR_REDUNDANCY_NONE_MINIMAL 0x0008 #define IPMI_SR_REDUNDANCY_NONE_REGAINED 0x0010 #define IPMI_SR_REDUNDANCY_NONE_INSUFFFICIENT 0x0020 #define IPMI_SR_REDUNDANCY_DEG_FROM_FULL 0x0040 #define IPMI_SR_REDUNDANCY_DEG_FROM_NON 0x0080 #define IPMI_SR_ACPI_DO 0x0001 #define IPMI_SR_ACPI_D1 0x0002 #define IPMI_SR_ACPI_D2 0x0004 #define IPMI_SR_ACPI_D3 0x0008 /* * Bitmasks for sensor-specific reading type (0x6F). See section 42.2. */ #define IPMI_ST_RESERVED 0x00 #define IPMI_ST_TEMP 0x01 #define IPMI_ST_VOLTAGE 0x02 #define IPMI_ST_CURRENT 0x03 #define IPMI_ST_FAN 0x04 #define IPMI_ST_PHYSICAL 0x05 #define IPMI_EV_PHYSICAL_GENERAL 0x0001 #define IPMI_EV_PHYSICAL_BAY 0x0002 #define IPMI_EV_PHYSICAL_CARD 0x0004 #define IPMI_EV_PHYSICAL_PROCESSOR 0x0008 #define IPMI_EV_PHYSICAL_LAN 0x0010 #define IPMI_EV_PHYSICAL_DOCK 0x0020 #define IPMI_EV_PHYSICAL_FAN 0x0040 #define IPMI_ST_PLATFORM 0x06 #define IPMI_EV_PLATFORM_SECURE 0x0001 #define IPMI_EV_PLATFORM_USER_PASS 0x0002 #define IPMI_EV_PLATFORM_SETUP_PASS 0x0004 #define IPMI_EV_PLATFORM_NETWORK_PASS 0x0008 #define IPMI_EV_PLATFORM_OTHER_PASS 0x0010 #define IPMI_EV_PLATFORM_OUT_OF_BAND 0x0020 #define IPMI_ST_PROCESSOR 0x07 #define IPMI_EV_PROCESSOR_IERR 0x0001 #define IPMI_EV_PROCESSOR_THERMAL 0x0002 #define IPMI_EV_PROCESSOR_FRB1 0x0004 #define IPMI_EV_PROCESSOR_FRB2 0x0008 #define IPMI_EV_PROCESSOR_FRB3 0x0010 #define IPMI_EV_PROCESSOR_CONFIG 0x0020 #define IPMI_EV_PROCESSOR_SMBIOS 0x0040 #define IPMI_EV_PROCESSOR_PRESENT 0x0080 #define IPMI_EV_PROCESSOR_DISABLED 0x0100 #define IPMI_EV_PROCESSOR_TERMINATOR 0x0200 #define IPMI_EV_PROCESSOR_THROTTLED 0x0400 #define IPMI_ST_POWER_SUPPLY 0x08 #define IPMI_EV_POWER_SUPPLY_PRESENT 0x0001 #define IPMI_EV_POWER_SUPPLY_FAILURE 0x0002 #define IPMI_EV_POWER_SUPPLY_PREDFAIL 0x0004 #define IPMI_EV_POWER_SUPPLY_INPUT_LOST 0x0008 #define IPMI_EV_POWER_SUPPLY_INPUT_RANGE 0x0010 #define IPMI_EV_POWER_SUPPLY_INPUT_RANGE_PRES 0x0020 #define IPMI_EV_POWER_SUPPLY_CONFIG_ERR 0x0040 #define IPMI_ST_POWER_UNIT 0x09 #define IPMI_EV_POWER_UNIT_OFF 0x0001 #define IPMI_EV_POWER_UNIT_CYCLE 0x0002 #define IPMI_EV_POWER_UNIT_240_DOWN 0x0004 #define IPMI_EV_POWER_UNIT_INTERLOCK_DOWN 0x0008 #define IPMI_EV_POWER_UNIT_AC_LOST 0x0010 #define IPMI_EV_POWER_UNIT_SOFT_FAILURE 0x0020 #define IPMI_EV_POWER_UNIT_FAIL 0x0040 #define IPMI_EV_POWER_UNIT_PREDFAIL 0x0080 #define IPMI_ST_COOLING 0x0A #define IPMI_ST_OTHER 0x0B #define IPMI_ST_MEMORY 0x0C #define IPMI_EV_MEMORY_CE 0x0001 #define IPMI_EV_MEMORY_UE 0x0002 #define IPMI_EV_MEMORY_PARITY 0x0004 #define IPMI_EV_MEMORY_SCRUB_FAIL 0x0008 #define IPMI_EV_MEMORY_DISABLED 0x0010 #define IPMI_EV_MEMORY_CE_LOG_LIMIT 0x0020 #define IPMI_EV_MEMORY_PRESENT 0x0040 #define IPMI_EV_MEMORY_CONFIG_ERR 0x0080 #define IPMI_EV_MEMORY_SPARE 0x0100 #define IPMI_EV_MEMORY_THROTTLED 0x0200 #define IPMI_EV_MEMORY_OVERTEMP 0x0400 #define IPMI_ST_BAY 0x0D #define IPMI_EV_BAY_PRESENT 0x0001 #define IPMI_EV_BAY_FAULT 0x0002 #define IPMI_EV_BAY_PREDFAIL 0x0004 #define IPMI_EV_BAY_SPARE 0x0008 #define IPMI_EV_BAY_CHECK 0x0010 #define IPMI_EV_BAY_CRITICAL 0x0020 #define IPMI_EV_BAY_FAILED 0x0040 #define IPMI_EV_BAY_REBUILDING 0x0080 #define IPMI_EV_BAY_ABORTED 0x0100 #define IPMI_ST_POST_RESIZE 0x0E #define IPMI_ST_FIRMWARE 0x0F #define IPMI_EV_FIRMWARE_ERROR 0x0001 #define IPMI_EV_FIRMWARE_HANG 0x0002 #define IPMI_EV_FIRMWARE_PROGRESS 0x0004 #define IPMI_ST_EVENT_LOG 0x10 #define IPMI_EV_EVENT_LOG_CE 0x0001 #define IPMI_EV_EVENT_LOG_TYPE 0x0002 #define IPMI_EV_EVENT_LOG_RESET 0x0004 #define IPMI_EV_EVENT_LOG_ALL 0x0008 #define IPMI_EV_EVENT_LOG_FULL 0x0010 #define IPMI_EV_EVENT_LOG_ALMOST_FULL 0x0020 #define IPMI_ST_WATCHDOG1 0x11 #define IPMI_EV_WATCHDOG_BIOS_RESET 0x0001 #define IPMI_EV_WATCHDOG_OS_RESET 0x0002 #define IPMI_EV_WATCHDOG_OS_SHUTDOWN 0x0004 #define IPMI_EV_WATCHDOG_OS_PWR_DOWN 0x0008 #define IPMI_EV_WATCHDOG_OS_PWR_CYCLE 0x0010 #define IPMI_EV_WATCHDOG_OS_NMI_DIAG 0x0020 #define IPMI_EV_WATCHDOG_EXPIRED 0x0040 #define IPMI_EV_WATCHDOG_PRE_TIMEOUT_INT 0x0080 #define IPMI_ST_SYSTEM 0x12 #define IPMI_EV_STSTEM_RECONF 0x0001 #define IPMI_EV_STSTEM_BOOT 0x0002 #define IPMI_EV_STSTEM_UNKNOWN_HW_FAILURE 0x0004 #define IPMI_EV_STSTEM_AUX_LOG_UPDATED 0x0008 #define IPMI_EV_STSTEM_PEF_ACTION 0x0010 #define IPMI_EV_SYSTEM_TIMETAMP_CLOCKSYNC 0x0020 #define IPMI_ST_CRITICAL 0x13 #define IPMI_EV_CRITICAL_EXT_NMI 0x0001 #define IPMI_EV_CRITICAL_BUS_TIMOEOUT 0x0002 #define IPMI_EV_CRITICAL_IO_NMI 0x0004 #define IPMI_EV_CRITICAL_SW_NMI 0x0008 #define IPMI_EV_CRITICAL_PCI_PERR 0x0010 #define IPMI_EV_CRITICAL_PCI_SERR 0x0020 #define IPMI_EV_CRITICAL_EISA_FAILSAFE 0x0040 #define IPMI_EV_CRITICAL_BUS_CE 0x0080 #define IPMI_EV_CRITICAL_BUS_UE 0x0100 #define IPMI_EV_CRITICAL_FATAL_NMI 0x0200 #define IPMI_EV_CRITICAL_BUS_FATAL_ERR 0x0400 #define IPMI_EV_CRITICAL_BUS_DEGRADED 0x0800 #define IPMI_ST_BUTTON 0x14 #define IPMI_EV_BUTTON_PWR 0x0001 #define IPMI_EV_BUTTON_SLEEP 0x0002 #define IPMI_EV_BUTTON_RESET 0x0004 #define IPMI_EV_BUTTON_FRU_LATCH 0x0008 #define IPMI_EV_BUTTON_FRU_SERVICE 0x0010 #define IPMI_ST_MODULE 0x15 #define IPMI_ST_MICROCONTROLLER 0x16 #define IPMI_ST_CARD 0x17 #define IPMI_ST_CHASSIS 0x18 #define IPMI_ST_CHIPSET 0x19 #define IPMI_EV_CHIPSET_PWR_CTL_FAIL 0x0001 #define IPMI_ST_FRU 0x1A #define IPMI_ST_CABLE 0x1B #define IPMI_EV_CABLE_CONNECTED 0x0001 #define IPMI_EV_CABLE_CONFIG_ERR 0x0002 #define IPMI_ST_TERMINATOR 0x1C #define IPMI_ST_BOOT 0x1D #define IPMI_EV_BOOT_BIOS_PWR_UP 0x0001 #define IPMI_EV_BOOT_BIOS_HARD_RESET 0x0002 #define IPMI_EV_BOOT_BIOS_WARM_RESET 0x0004 #define IPMI_EV_BOOT_PXE_BOOT 0x0008 #define IPMI_EV_BOOT_DIAG_BOOT 0x0010 #define IPMI_EV_BOOT_OS_HARD_RESET 0x0020 #define IPMI_EV_BOOT_OS_WARM_RESET 0x0040 #define IPMI_EV_BOOT_SYS_RESTART 0x0080 #define IPMI_ST_BOOT_ERROR 0x1E #define IPMI_EV_BOOT_ERROR_NOMEDIA 0x0001 #define IPMI_EV_BOOT_ERROR_NON_BOOTABLE_DISK 0x0002 #define IPMI_EV_BOOT_ERROR_NO_PXE_SERVER 0x0004 #define IPMI_EV_BOOT_ERROR_INV_BOOT_SECT 0x0008 #define IPMI_EV_BOOT_ERROR_USR_SELECT_TIMEOUT 0x0010 #define IPMI_ST_BOOT_OS 0x1F #define IPMI_EV_BOOT_OS_A_DRV_BOOT_COMPLETE 0x0001 #define IPMI_EV_BOOT_OS_C_DRV_BOOT_COMPLETE 0x0002 #define IPMI_EV_BOOT_OS_PXE_BOOT_COMPLETE 0x0004 #define IPMI_EV_BOOT_OS_DIAG_BOOT_COMPLETE 0x0008 #define IPMI_EV_BOOT_OS_CDROM_BOOT_COMPLETE 0x0010 #define IPMI_EV_BOOT_OS_ROM_BOOT_COMPLETE 0x0020 #define IPMI_EV_BOOT_OS_UNSPEC_BOOT_COMPLETE 0x0040 #define IPMI_ST_OS_SHUTDOWN 0x20 #define IPMI_EV_OS_SHUTDOWN_LOADING 0x0001 #define IPMI_EV_OS_SHUTDOWN_CRASH 0x0002 #define IPMI_EV_OS_STOP_GRACEFUL 0x0004 #define IPMI_EV_OS_SHUTDOWN_GRACEFUL 0x0008 #define IPMI_EV_OS_SHUTDOWN_PEF 0x0010 #define IPMI_EV_OS_SHUTDOWN_BMC 0x0020 #define IPMI_ST_SLOT 0x21 #define IPMI_EV_SLOT_FAULT_ASSERTED 0x0001 #define IPMI_EV_SLOT_IDENTIFY_ASSERTED 0x0002 #define IPMI_EV_SLOT_CONNECTED 0x0004 #define IPMI_EV_SLOT_INSTALL_READY 0x0008 #define IPMI_EV_SLOT_REMOVE_READY 0x0010 #define IPMI_EV_SLOT_PWR_OFF 0x0020 #define IPMI_EV_SLOT_REMOVED 0x0040 #define IPMI_EV_SLOT_INTERLOCK_ASSERTED 0x0080 #define IPMI_EV_SLOT_DISABLED 0x0100 #define IPMI_EV_SLOT_SPARE_DEVICE 0x0200 #define IPMI_ST_ACPI 0x22 #define IPMI_EV_ACPI_PSTATE_S0_G0 0x0001 #define IPMI_EV_ACPI_PSTATE_S1 0x0002 #define IPMI_EV_ACPI_PSTATE_S2 0x0004 #define IPMI_EV_ACPI_PSTATE_S3 0x0008 #define IPMI_EV_ACPI_PSTATE_S4 0x0010 #define IPMI_EV_ACPI_PSTATE_S5_G2_SOFT_OFF 0x0020 #define IPMI_EV_ACPI_PSTATE_S4_S5_SOFT_OFF 0x0040 #define IPMI_EV_ACPI_PSATTE_G3_MECH_OFF 0x0080 #define IPMI_EV_ACPI_PSTATE_S1_S2_S3_SLEEP 0x0100 #define IPMI_EV_ACPI_PSTATE_G1_SLEEP 0x0200 #define IPMI_EV_ACPI_PSTATE_S5_OVERRIDE 0x0400 #define IPMI_EV_ACPI_PSTATE_LEGACY_ON 0x0800 #define IPMI_EV_ACPI_PSTATE_LEGACY_OFF 0x1000 #define IPMI_EV_ACPI_PSTATE_UNKNOWN 0x2000 #define IPMI_ST_WATCHDOG2 0x23 #define IPMI_EV_WATCHDOG2_EXPIRED 0x0001 #define IPMI_EV_WATCHDOG2_HARD_RESET 0x0002 #define IPMI_EV_WATCHDOG2_PWR_DOWN 0x0004 #define IPMI_EV_WATCHDOG2_PWR_CYCLE 0x0008 #define IPMI_EV_WATCHDOG2_RESERVED1 0x0010 #define IPMI_EV_WATCHDOG2_RESERVED2 0x0020 #define IPMI_EV_WATCHDOG2_RESERVED3 0x0040 #define IPMI_EV_WATCHDOG2_RESERVED4 0x0080 #define IPMI_EV_WATCHDOG2_TIMEOUT_INT 0x0100 #define IPMI_ST_ALERT 0x24 #define IPMI_EV_ALERT_PLAT_PAGE 0x0001 #define IPMI_EV_ALERT_PLAT_LAN_ALERT 0x0002 #define IPMI_EV_ALERT_PLAT_EVT_TRAP 0x0004 #define IPMI_EV_ALERT_PLAT_SNMP_TRAP 0x0008 #define IPMI_ST_PRESENCE 0x25 #define IPMI_EV_PRESENCE_PRESENT 0x0001 #define IPMI_EV_PRESENCE_ABSENT 0x0002 #define IPMI_EV_PRESENCE_DISABLED 0x0004 #define IPMI_ST_ASIC 0x26 #define IPMI_ST_LAN 0x27 #define IPMI_EV_LAN_HEARTBEAT_LOST 0x0001 #define IPMI_EV_LAN_HEARTBEAT 0x0002 #define IPMI_ST_HEALTH 0x28 #define IPMI_EV_HEALTH_SENSOR_ACC_DEGRADED 0x0001 #define IPMI_EV_HEALTH_CNTLR_ACC_DEGRADED 0x0002 #define IPMI_EV_HEALTH_CNTLR_OFFLINE 0x0004 #define IPMI_EV_HEALTH_CNTLR_UNAVAIL 0x0008 #define IPMI_EV_HEALTH_SENSOR_FAILURE 0x0010 #define IPMI_EV_HEALTH_FRU_FAILURE 0x0020 #define IPMI_ST_BATTERY 0x29 #define IPMI_EV_BATTERY_LOW 0x0001 #define IPMI_EV_BATTERY_FAILED 0x0002 #define IPMI_EV_BATTERY_PRESENCE 0x0004 #define IPMI_ST_AUDIT 0x2A #define IPMI_EV_AUDIT_SESSION_ACTIVATED 0x0001 #define IPMI_EV_AUDIT_SESSION_DEACTIVATED 0x0002 #define IPMI_ST_VERSION 0x2B #define IPMI_EV_VERSION_HW_CHANGE 0x0001 #define IPMI_EV_VERSION_SW_CHANGE 0x0002 #define IPMI_EV_VERSION_HW_INCOMPATIBLE 0x0004 #define IPMI_EV_VERSION_SW_INCOMPATIBLE 0x0008 #define IPMI_EV_VERSION_HW_INVAL 0x0010 #define IPMI_EV_VERSION_SW_INVAL 0x0020 #define IPMI_EV_VERSION_HW_CHANGE_SUCCESS 0x0040 #define IPMI_EV_VERSION_SW_CHANGE_SUCCESS 0x0080 #define IPMI_ST_FRU_STATE 0x2C #define IPMI_EV_FRU_STATE_NOT_INSTALLED 0x0001 #define IPMI_EV_FRU_STATE_INACTIVE 0x0002 #define IPMI_EV_FRU_STATE_ACT_REQ 0x0004 #define IPMI_EV_FRU_STATE_ACT_INPROGRESS 0x0008 #define IPMI_EV_FRU_STATE_ACTIVE 0x0010 #define IPMI_EV_FRU_STATE_DEACT_REQ 0x0020 #define IPMI_EV_FRU_STATE_DEACT_INPROGRESS 0x0040 #define IPMI_EV_FRU_STATE_COMM_LOST 0x0080 /* * Constants for unit type codes. See Table 43-15. */ #define IPMI_UNITS_UNSPECIFIED 0x00 #define IPMI_UNITS_DEGREES_C 0x01 #define IPMI_UNITS_DEGREES_F 0x02 #define IPMI_UNITS_DEGREES_K 0x03 #define IPMI_UNITS_VOLTS 0x04 #define IPMI_UNITS_AMPS 0x05 #define IPMI_UNITS_WATTS 0x06 #define IPMI_UNITS_JOULES 0x07 #define IPMI_UNITS_COULOMBS 0x08 #define IPMI_UNITS_VA 0x09 #define IPMI_UNITS_NITS 0x0A #define IPMI_UNITS_LUMEN 0x0B #define IPMI_UNITS_LUX 0x0C #define IPMI_UNITS_CANDELA 0x0D #define IPMI_UNITS_KPA 0x0E #define IPMI_UNITS_PSI 0x0F #define IPMI_UNITS_NEWTON 0x10 #define IPMI_UNITS_CFM 0x11 #define IPMI_UNITS_RPM 0x12 #define IPMI_UNITS_HZ 0x13 #define IPMI_UNITS_MICROSEC 0x14 #define IPMI_UNITS_MILLISEC 0x15 #define IPMI_UNITS_SECS 0x16 #define IPMI_UNITS_MIN 0x17 #define IPMI_UNITS_HOUR 0x18 #define IPMI_UNITS_DAY 0x19 #define IPMI_UNITS_WEEK 0x1A #define IPMI_UNITS_MIL 0x1B #define IPMI_UNITS_INCHES 0x1C #define IPMI_UNITS_FEET 0x1D #define IPMI_UNITS_CUB_INCH 0x1E #define IPMI_UNITS_CUB_FEET 0x1F #define IPMI_UNITS_MM 0x20 #define IPMI_UNITS_CM 0x21 #define IPMI_UNITS_METERS 0x22 #define IPMI_UNITS_CUB_CM 0x23 #define IPMI_UNITS_CUB_METER 0x24 #define IPMI_UNITS_LITERS 0x25 #define IPMI_UNITS_FLUID_OUNCE 0x26 #define IPMI_UNITS_RADIANS 0x27 #define IPMI_UNITS_STERADIANS 0x28 #define IPMI_UNITS_REVOLUTIONS 0x29 #define IPMI_UNITS_CYCLES 0x2A #define IPMI_UNITS_GRAVITIES 0x2B #define IPMI_UNITS_OUNCE 0x2C #define IPMI_UNITS_POUND 0x2D #define IPMI_UNITS_FOOT_POUND 0x2E #define IPMI_UNITS_OZ_INCH 0x2F #define IPMI_UNITS_GAUSS 0x30 #define IPMI_UNITS_GILBERTS 0x31 #define IPMI_UNITS_HENRY 0x32 #define IPMI_UNITS_MILHENRY 0x33 #define IPMI_UNITS_FARAD 0x34 #define IPMI_UNITS_MICROFARAD 0x35 #define IPMI_UNITS_OHMS 0x36 #define IPMI_UNITS_SIEMENS 0x37 #define IPMI_UNITS_MOLE 0x38 #define IPMI_UNITS_BECQUEREL 0x39 #define IPMI_UNITS_PPM 0x3A /* 0x3B is reserved */ #define IPMI_UNITS_DECIBELS 0x3C #define IPMI_UNITS_DBA 0x3D #define IPMI_UNITS_DBC 0x3E #define IPMI_UNITS_GRAY 0x3F #define IPMI_UNITS_SIEVERT 0x40 #define IPMI_UNITS_COLOR_TEMP_K 0x41 #define IPMI_UNITS_BIT 0x42 #define IPMI_UNITS_KILOBIT 0x43 #define IPMI_UNITS_MEGABIT 0x44 #define IPMI_UNITS_GIGABIT 0x45 #define IPMI_UNITS_BYTE 0x46 #define IPMI_UNITS_KILOBYTE 0x47 #define IPMI_UNITS_MEGABYTE 0x48 #define IPMI_UNITS_GIGABYTE 0x49 #define IPMI_UNITS_WORD 0x4A #define IPMI_UNITS_DWORD 0x4B #define IPMI_UNITS_QWORD 0x4C #define IPMI_UNITS_MEMLINE 0x4D #define IPMI_UNITS_HIT 0x4E #define IPMI_UNITS_MISS 0x4F #define IPMI_UNITS_RETRY 0x50 #define IPMI_UNITS_RESET 0x51 #define IPMI_UNITS_OVERFLOW 0x52 #define IPMI_UNITS_UNDERRUN 0x53 #define IPMI_UNITS_COLLISION 0x54 #define IPMI_UNITS_PACKETS 0x55 #define IPMI_UNITS_MESSAGES 0x56 #define IPMI_UNITS_CHARACTERS 0x57 #define IPMI_UNITS_ERROR 0x58 #define IPMI_UNITS_CE 0x59 #define IPMI_UNITS_UE 0x5A #define IPMI_UNITS_FATAL_ERROR 0x5B #define IPMI_UNITS_GRAMS 0x5C /* * Event-Only Record. See section 43.3. */ #define IPMI_SDR_TYPE_EVENT_ONLY 0x03 typedef struct ipmi_sdr_event_only { /* RECORD KEY BYTES */ uint8_t is_eo_owner; DECL_BITFIELD3( is_eo_sensor_lun :2, is_eo_fru_lun :2, is_eo_channel :4); uint8_t is_eo_number; /* RECORD BODY BYTES */ uint8_t is_eo_entity_id; DECL_BITFIELD2( is_eo_entity_instance :7, is_eo_entity_logical :1); uint8_t is_eo_sensor_type; uint8_t is_eo_reading_type; DECL_BITFIELD3( is_eo_share_count :4, is_eo_modifier_type :2, is_eo_direction :2); DECL_BITFIELD2( is_eo_modifier_offset :7, is_eo_sharing :1); uint8_t __reserved; uint8_t is_eo_oem; DECL_BITFIELD3( is_eo_idlen :5, __reserved1 :1, is_eo_idtype :2); char is_eo_idstring[1]; } ipmi_sdr_event_only_t; /* * Entity Association Record. See section 43.4. */ #define IPMI_SDR_TYPE_ENTITY_ASSOCIATION 0x08 typedef struct ipmi_sdr_entity_association { /* RECORD KEY BYTES */ uint8_t is_ea_entity_id; uint8_t is_ea_entity_instance; DECL_BITFIELD4( __reserved :5, is_ea_presence :1, is_ea_record_link :1, is_ea_range :1); /* RECORD BODY BYTES */ struct { uint8_t is_ea_sub_id; uint8_t is_ea_sub_instance; } is_ea_sub[4]; } ipmi_sdr_entity_association_t; /* * Device-relative Entity Association Record. See section 43.5. */ #define IPMI_SDR_TYPE_DEVICE_RELATIVE 0x09 typedef struct ipmi_sdr_device_relative { /* RECORD KEY BYTES */ uint8_t is_dr_entity_id; uint8_t is_dr_entity_instance; DECL_BITFIELD2( __reserved1 :1, is_dr_slaveaddr :7); DECL_BITFIELD2( __reserved2 :4, is_dr_channel :4); DECL_BITFIELD4( __reserved :5, is_dr_presence :1, is_dr_record_link :1, is_dr_range :1); /* RECORD BODY BYTES */ struct { DECL_BITFIELD2( __reserved3 :1, is_dr_sub_slaveaddr :7); DECL_BITFIELD2( __reserved4 :4, is_dr_sub_channel :4); uint8_t is_ea_sub_id; uint8_t is_ea_sub_instance; } is_ea_sub[4]; } ipmi_sdr_device_relative_t; /* * Generic Device Locator Record. See section 43.7. */ #define IPMI_SDR_TYPE_GENERIC_LOCATOR 0x10 typedef struct ipmi_sdr_generic_locator { /* RECORD KEY BYTES */ DECL_BITFIELD2( __reserved1 :1, is_gl_accessaddr :7); DECL_BITFIELD2( is_gl_channel_msb :1, is_gl_slaveaddr :7); DECL_BITFIELD3( is_gl_bus :3, is_gl_lun :2, is_gl_channel :3); /* RECORD BODY BYTES */ DECL_BITFIELD2( is_gl_span :3, __reserved2 :5); uint8_t __reserved3; uint8_t is_gl_type; uint8_t is_gl_modifier; uint8_t is_gl_entity; uint8_t is_gl_instance; uint8_t is_gl_oem; DECL_BITFIELD3( is_gl_idlen :5, __reserved4 :1, is_gl_idtype :2); char is_gl_idstring[1]; } ipmi_sdr_generic_locator_t; /* * FRU Device Locator Record. See section 43.8. */ #define IPMI_SDR_TYPE_FRU_LOCATOR 0x11 typedef struct ipmi_sdr_fru_locator { /* RECORD KEY BYTES */ DECL_BITFIELD2( __reserved1 :1, is_fl_accessaddr :7); union { struct { uint8_t _is_fl_devid; } _logical; struct { DECL_BITFIELD2( __reserved :1, _is_fl_slaveaddr :7); } _nonintelligent; } _devid_or_slaveaddr; DECL_BITFIELD4( is_fl_bus :3, is_fl_lun :2, __reserved2 :2, is_fl_logical :1); DECL_BITFIELD2( __reserved3 :4, is_fl_channel :4); /* RECORD BODY BYTES */ uint8_t __reserved4; uint8_t is_fl_type; uint8_t is_fl_modifier; uint8_t is_fl_entity; uint8_t is_fl_instance; uint8_t is_fl_oem; DECL_BITFIELD3( is_fl_idlen :5, __reserved5 :1, is_fl_idtype :2); char is_fl_idstring[1]; } ipmi_sdr_fru_locator_t; #define is_fl_devid _devid_or_slaveaddr._logical._is_fl_devid #define is_fl_slaveaddr _devid_or_slaveaddr._nonintelligent._is_fl_slaveaddr /* * Management Controller Device Locator Record. See section 43.9 */ #define IPMI_SDR_TYPE_MANAGEMENT_LOCATOR 0x12 typedef struct ipmi_sdr_management_locator { /* RECORD KEY BYTES */ DECL_BITFIELD2( __reserved1 :1, is_ml_devaddr :7); DECL_BITFIELD2( is_ml_channel :4, __reserved2 :4); /* RECORD BODY BYTES */ DECL_BITFIELD7( is_ml_init_message :2, is_ml_init_log :1, is_ml_init_controller_log :1, __reserved3 :1, is_ml_static :1, is_ml_acpi_device :1, is_ml_acpi_system :1); DECL_BITFIELD8( is_ml_supp_sensor :1, is_ml_supp_sdr :1, is_ml_supp_sel :1, is_ml_supp_fru :1, is_ml_supp_event_receiver :1, is_ml_supp_event_generator :1, is_ml_supp_bridge :1, is_ml_supp_chassis :1); uint8_t __reserved4; uint16_t __reserved5; uint8_t is_ml_entity_id; uint8_t is_ml_entity_instance; uint8_t is_ml_oem; DECL_BITFIELD3( is_ml_idlen :5, __reserved6 :1, is_ml_idtype :2); char is_ml_idstring[1]; } ipmi_sdr_management_locator_t; #define IPMI_MESSAGE_INIT_ENABLE 0x0 #define IPMI_MESSAGE_INIT_DISABLE 0x1 #define IPMI_MESSAGE_INIT_NONE 0x2 /* * Management Controller Confirmation Record. See section 43.10 */ #define IPMI_SDR_TYPE_MANAGEMENT_CONFIRMATION 0x13 typedef struct ipmi_sdr_management_confirmation { /* RECORD KEY BYTES */ DECL_BITFIELD2( __reserved1 :1, is_mc_slaveaddr :7); uint8_t is_mc_deviceid; DECL_BITFIELD2( is_mc_dev_revision :4, is_mc_channel :4); /* RECORD BODY BYTES */ DECL_BITFIELD2( is_mc_major_rev :7, __reserved2 :1); uint8_t is_mc_minor_rev; uint8_t is_mc_impi_ver; uint8_t is_mc_manufacturer[3]; uint16_t is_mc_product; uint8_t is_mc_guid[16]; } ipmi_sdr_management_confirmation_t; /* * BMC Message Channel Info Record. See esction 43.11. */ #define IPMI_SDR_TYPE_BMC_MESSAGE_CHANNEL 0x14 typedef struct ipmi_sdr_bmc_channel { /* RECORD BODY BYTES */ struct { DECL_BITFIELD3( is_bc_protocol :4, is_bc_receive_lun :3, is_bc_transmit :1); } is_bc_channel[8]; uint8_t is_bc_interrupt_type; uint8_t is_bc_buffer_type; uint8_t __reserved; } ipmi_sdr_bmc_channel_t; /* * OEM Record. See ction 43.12. */ #define IPMI_SDR_TYPE_OEM 0xC0 typedef struct ipmi_sdr_oem { uint8_t is_oem_manufacturer[3]; uint8_t is_oem_data[1]; } ipmi_sdr_oem_t; /* * Iterate over the SDR repository. This function does the work of parsing the * name when available, and keeping the repository in a consistent state. */ extern int ipmi_sdr_iter(ipmi_handle_t *, int (*)(ipmi_handle_t *, const char *, ipmi_sdr_t *, void *), void *); /* * Lookup the given sensor type by name or a combination of name and entity * ID/instance. These functions automatically read in and cache the complete * SDR repository. */ extern ipmi_sdr_t *ipmi_sdr_lookup(ipmi_handle_t *, const char *); extern ipmi_sdr_t *ipmi_sdr_lookup_precise(ipmi_handle_t *, const char *, uint8_t, uint8_t); extern ipmi_sdr_fru_locator_t *ipmi_sdr_lookup_fru(ipmi_handle_t *, const char *); extern ipmi_sdr_generic_locator_t *ipmi_sdr_lookup_generic(ipmi_handle_t *, const char *); extern ipmi_sdr_compact_sensor_t *ipmi_sdr_lookup_compact_sensor( ipmi_handle_t *, const char *); extern ipmi_sdr_full_sensor_t *ipmi_sdr_lookup_full_sensor( ipmi_handle_t *, const char *); /* * Entity ID codes. See table 43.13. */ #define IPMI_ET_UNSPECIFIED 0x00 #define IPMI_ET_OTHER 0x01 #define IPMI_ET_UNKNOWN 0x02 #define IPMI_ET_PROCESSOR 0x03 #define IPMI_ET_DISK 0x04 #define IPMI_ET_PERIPHERAL 0x05 #define IPMI_ET_MANAGEMENT_MODULE 0x06 #define IPMI_ET_MOTHERBOARD 0x07 #define IPMI_ET_MEMORY_MODULE 0x08 #define IPMI_ET_PROCESSOR_MODULE 0x09 #define IPMI_ET_PSU 0x0A #define IPMI_ET_CARD 0x0B #define IPMI_ET_FRONT_PANEL 0x0C #define IPMI_ET_BACK_PANEL 0x0D #define IPMI_ET_POWER_BOARD 0x0E #define IPMI_ET_BACKPLANE 0x0F #define IPMI_ET_EXPANSION_BOARD 0x10 #define IPMI_ET_OTHER_BOARD 0x11 #define IPMI_ET_PROCESSOR_BOARD 0x12 #define IPMI_ET_POWER_DOMAIN 0x13 #define IPMI_ET_POWER_CONVERTER 0x14 #define IPMI_ET_POWER_MANAGEMENT 0x15 #define IPMI_ET_BACK_CHASSIS 0x16 #define IPMI_ET_SYSTEM_CHASSIS 0x17 #define IPMI_ET_SUB_CHASSIS 0x18 #define IPMI_ET_OTHER_CHASSIS 0x19 #define IPMI_ET_DISK_BAY 0x1A #define IPMI_ET_PERIPHERAL_BAY 0x1B #define IPMI_ET_DEVICE_BAY 0x1C #define IPMI_ET_FAN 0x1D #define IPMI_ET_COOLING_DOMAIN 0x1E #define IPMI_ET_CABLE 0x1F #define IPMI_ET_MEMORY_DEVICE 0x20 #define IPMI_ET_MANAGEMENT_SOFTWARE 0x21 #define IPMI_ET_SYSTEM_FIRMWARE 0x22 #define IPMI_ET_OS 0x23 #define IPMI_ET_SYSTEM_BUS 0x24 #define IPMI_ET_GROUP 0x25 #define IPMI_ET_REMOTE 0x26 #define IPMI_ET_ENVIRONMENT 0x27 #define IPMI_ET_BATTERY 0x28 #define IPMI_ET_BLADE 0x29 #define IPMI_ET_SWITCH 0x2A #define IPMI_ET_PROCMEM_MODULE 0x2B #define IPMI_ET_IO_MODULE 0x2C #define IPMI_ET_PROCIO_MODULE 0x2D #define IPMI_ET_CONTROLLER_FIRMWARE 0x2E #define IPMI_ET_CHANNEL 0x2F #define IPMI_ET_PCI 0x30 #define IPMI_ET_PCIE 0x31 #define IPMI_ET_SCSI 0x32 #define IPMI_ET_SATA_SAS 0x33 #define IPMI_ET_FSB 0x34 #define IPMI_ET_RTC 0x35 /* * Get Sensor Threshold. See section 35.9 */ #define IPMI_CMD_GET_SENSOR_THRESHOLDS 0x27 typedef struct ipmi_sensor_thresholds { uint8_t ithr_readable_mask; uint8_t ithr_lower_noncrit; uint8_t ithr_lower_crit; uint8_t ithr_lower_nonrec; uint8_t ithr_upper_noncrit; uint8_t ithr_upper_crit; uint8_t ithr_upper_nonrec; } ipmi_sensor_thresholds_t; extern int ipmi_get_sensor_thresholds(ipmi_handle_t *, ipmi_sensor_thresholds_t *, uint8_t); /* * Get Sensor Reading. See section 35.14. */ #define IPMI_CMD_GET_SENSOR_READING 0x2d typedef struct ipmi_sensor_reading { uint8_t isr_reading; DECL_BITFIELD4( __reserved1 :5, isr_state_unavailable :1, isr_scanning_enabled :1, isr_event_enabled :1); uint16_t isr_state; } ipmi_sensor_reading_t; #define IPMI_SENSOR_THRESHOLD_LOWER_NONCRIT 0x0001 #define IPMI_SENSOR_THRESHOLD_LOWER_CRIT 0x0002 #define IPMI_SENSOR_THRESHOLD_LOWER_NONRECOV 0x0004 #define IPMI_SENSOR_THRESHOLD_UPPER_NONCRIT 0x0008 #define IPMI_SENSOR_THRESHOLD_UPPER_CRIT 0x0010 #define IPMI_SENSOR_THRESHOLD_UPPER_NONRECOV 0x0020 extern ipmi_sensor_reading_t *ipmi_get_sensor_reading(ipmi_handle_t *, uint8_t); extern int ipmi_sdr_conv_reading(ipmi_sdr_full_sensor_t *, uint8_t, double *); /* * Set Sensor Reading. See section 35.14. */ #define IPMI_CMD_SET_SENSOR_READING 0x30 #define IPMI_SENSOR_OP_CLEAR 0x3 /* clear '0' bits */ #define IPMI_SENSOR_OP_SET 0x2 /* set '1' bits */ #define IPMI_SENSOR_OP_EXACT 0x1 /* set bits exactly */ typedef struct ipmi_set_sensor_reading { uint8_t iss_id; DECL_BITFIELD5( iss_set_reading :1, __reserved :1, iss_deassrt_op :2, iss_assert_op :2, iss_data_bytes :2); uint8_t iss_sensor_reading; uint16_t iss_assert_state; /* optional */ uint16_t iss_deassert_state; /* optional */ uint8_t iss_event_data1; /* optional */ uint8_t iss_event_data2; /* optional */ uint8_t iss_event_data3; /* optional */ } ipmi_set_sensor_reading_t; extern int ipmi_set_sensor_reading(ipmi_handle_t *, ipmi_set_sensor_reading_t *); /* * These IPMI message id/opcodes are documented in Appendix G in the IPMI spec. * * Payloads for these two commands are described in Sections 34.1 and 34.2 of * the spec, respectively. */ #define IPMI_CMD_GET_FRU_INV_AREA 0x10 #define IPMI_CMD_READ_FRU_DATA 0x11 /* * Structs to hold the FRU Common Header and the FRU Product Info Area, as * described in the IPMI Platform Management FRU Information Storage * Definition (v1.1). */ typedef struct ipmi_fru_hdr { uint8_t ifh_format; uint8_t ifh_int_use_off; uint8_t ifh_chassis_info_off; uint8_t ifh_board_info_off; uint8_t ifh_product_info_off; uint8_t ifh_multi_rec_off; uint8_t ifh_pad; uint8_t ifh_chksum; } ipmi_fru_hdr_t; /* * Because only 6 bits are used to specify the length of each field in the FRU * product and board info areas, the biggest string we would ever need to hold * would be 63 chars plus a NULL. */ #define FRU_INFO_MAXLEN 64 typedef struct ipmi_fru_brd_info { char ifbi_manuf_date[3]; char ifbi_manuf_name[FRU_INFO_MAXLEN]; char ifbi_board_name[FRU_INFO_MAXLEN]; char ifbi_product_serial[FRU_INFO_MAXLEN]; char ifbi_part_number[FRU_INFO_MAXLEN]; } ipmi_fru_brd_info_t; typedef struct ipmi_fru_prod_info { char ifpi_manuf_name[FRU_INFO_MAXLEN]; char ifpi_product_name[FRU_INFO_MAXLEN]; char ifpi_part_number[FRU_INFO_MAXLEN]; char ifpi_product_version[FRU_INFO_MAXLEN]; char ifpi_product_serial[FRU_INFO_MAXLEN]; char ifpi_asset_tag[FRU_INFO_MAXLEN]; } ipmi_fru_prod_info_t; extern int ipmi_fru_read(ipmi_handle_t *, ipmi_sdr_fru_locator_t *, char **); extern int ipmi_fru_parse_board(ipmi_handle_t *, char *, ipmi_fru_brd_info_t *); extern int ipmi_fru_parse_product(ipmi_handle_t *, char *, ipmi_fru_prod_info_t *); /* * Routines to convert from entity and sensors defines into text strings. */ void ipmi_entity_name(uint8_t, char *, size_t); void ipmi_sensor_type_name(uint8_t, char *, size_t); void ipmi_sensor_units_name(uint8_t, char *, size_t); void ipmi_sensor_reading_name(uint8_t, uint8_t, char *, size_t); /* * Entity management. IPMI has a notion of 'entities', but these are not * directly accessible from any commands. Instead, their existence is inferred * from examining the SDR repository. Since this is rather unwieldy, and * iterating over entities is a common operation, libipmi provides an entity * abstraction that hides the implementation details. This handles entity * groupings as well as SDR associations. */ typedef struct ipmi_entity { uint8_t ie_type; uint8_t ie_instance; uint8_t ie_children; boolean_t ie_logical; } ipmi_entity_t; extern int ipmi_entity_iter(ipmi_handle_t *, int (*)(ipmi_handle_t *, ipmi_entity_t *, void *), void *); extern int ipmi_entity_iter_sdr(ipmi_handle_t *, ipmi_entity_t *, int (*)(ipmi_handle_t *, ipmi_entity_t *, const char *, ipmi_sdr_t *, void *), void *); extern int ipmi_entity_iter_children(ipmi_handle_t *, ipmi_entity_t *, int (*)(ipmi_handle_t *, ipmi_entity_t *, void *), void *); extern ipmi_entity_t *ipmi_entity_lookup(ipmi_handle_t *, uint8_t, uint8_t); extern ipmi_entity_t *ipmi_entity_lookup_sdr(ipmi_handle_t *, const char *); extern ipmi_entity_t *ipmi_entity_parent(ipmi_handle_t *, ipmi_entity_t *); extern int ipmi_entity_present(ipmi_handle_t *, ipmi_entity_t *, boolean_t *); extern int ipmi_entity_present_sdr(ipmi_handle_t *, ipmi_sdr_t *, boolean_t *); /* * User management. The raw functions are private to libipmi, and only the * higher level abstraction (ipmi_user_t) is exported to consumers of the * library. */ #define IPMI_USER_PRIV_CALLBACK 0x1 #define IPMI_USER_PRIV_USER 0x2 #define IPMI_USER_PRIV_OPERATOR 0x3 #define IPMI_USER_PRIV_ADMIN 0x4 #define IPMI_USER_PRIV_OEM 0x5 #define IPMI_USER_PRIV_NONE 0xf typedef struct ipmi_user { uint8_t iu_uid; char *iu_name; boolean_t iu_enabled; boolean_t iu_ipmi_msg_enable; boolean_t iu_link_auth_enable; uint8_t iu_priv; } ipmi_user_t; extern int ipmi_user_iter(ipmi_handle_t *, int (*)(ipmi_user_t *, void *), void *); extern ipmi_user_t *ipmi_user_lookup_name(ipmi_handle_t *, const char *); extern ipmi_user_t *ipmi_user_lookup_id(ipmi_handle_t *, uint8_t); extern int ipmi_user_set_password(ipmi_handle_t *, uint8_t, const char *); /* * The remaining functions are private to the implementation of the Sun ILOM * service processor. These function first check the manufacturer from the IPMI * device ID, and will return EIPMI_NOT_SUPPORTED if attempted for non-Sun * devices. */ boolean_t ipmi_is_sun_ilom(ipmi_deviceid_t *); /* * Sun OEM LED requests. */ #define IPMI_SUNOEM_LED_MODE_OFF 0 #define IPMI_SUNOEM_LED_MODE_ON 1 #define IPMI_SUNOEM_LED_MODE_STANDBY 2 #define IPMI_SUNOEM_LED_MODE_SLOW 3 #define IPMI_SUNOEM_LED_MODE_FAST 4 /* * These functions take a SDR record and construct the appropriate form of the * above commands. */ extern int ipmi_sunoem_led_set(ipmi_handle_t *, ipmi_sdr_generic_locator_t *, uint8_t); extern int ipmi_sunoem_led_get(ipmi_handle_t *, ipmi_sdr_generic_locator_t *, uint8_t *); /* * Sun OEM uptime. Note that the underlying command returns the uptime in big * endian form. This wrapper automatically converts to the appropriate native * form. */ #define IPMI_CMD_SUNOEM_UPTIME 0x08 extern int ipmi_sunoem_uptime(ipmi_handle_t *, uint32_t *, uint32_t *); /* * Sun OEM FRU update. The FRU information is managed through a generic * identifier, and then a type-specific data portion. The wrapper function will * automatically fill in the data length field according to which type is * specified. */ #define IPMI_CMD_SUNOEM_FRU_UPDATE 0x16 #define IPMI_SUNOEM_FRU_DIMM 0x00 #define IPMI_SUNOEM_FRU_CPU 0x01 #define IPMI_SUNOEM_FRU_BIOS 0x02 #define IPMI_SUNOEM_FRU_DISK 0x03 typedef struct ipmi_sunoem_fru { uint8_t isf_type; uint8_t isf_id; uint8_t isf_datalen; union { struct { uint8_t isf_data[128]; } dimm; struct { uint32_t isf_thermtrip; uint32_t isf_eax; char isf_product[48]; } cpu; struct { char isf_part[16]; char isf_version[16]; } bios; struct { char isf_manufacturer[16]; char isf_model[28]; char isf_serial[20]; char isf_version[8]; char isf_capacity[16]; } disk; } isf_data; } ipmi_sunoem_fru_t; int ipmi_sunoem_update_fru(ipmi_handle_t *, ipmi_sunoem_fru_t *); /* * See section 28.2 */ #define IPMI_CMD_GET_CHASSIS_STATUS 0x01 /* * flags for ichs_current_pwr_state field */ #define IPMI_CURR_PWR_STATE_ON 0x01 #define IPMI_CURR_PWR_STATE_OVERLOAD 0x02 #define IPMI_CURR_PWR_STATE_INTERLOCK 0x04 #define IPMI_CURR_PWR_STATE_FAULT 0x08 #define IPMI_CURR_PWR_STATE_CNTL_FAULT 0x10 /* * flags for ichs_last_pwr_state field */ #define IPMI_LAST_PWR_STATE_ACFAILED 0x01 #define IPMI_LAST_PWR_STATE_OVERLOAD 0x02 #define IPMI_LAST_PWR_STATE_INTERLOCK 0x04 #define IPMI_LAST_PWR_STATE_FAULT 0x08 #define IPMI_LAST_PWR_STATE_CMD_ON 0x10 /* * flags for the ichs_pwr_restore_policy field */ #define IPMI_PWR_POLICY_REMAIN_OFF 0x0 #define IPMI_PWR_POLICY_RESTORE 0x1 #define IPMI_PWR_POLICY_POWER_ON 0x2 #define IPMI_PWR_POLICY_UNKNOWN 0x3 typedef struct ipmi_chassis_status { DECL_BITFIELD3( ichs_current_pwr_state :5, ichs_pwr_restore_policy :2, __reserved1 :1); DECL_BITFIELD2( ichs_last_pwr_state :5, __reserved2 :3); DECL_BITFIELD7( ichs_intrusion_asserted :1, ichs_front_panel_disabled :1, ichs_drive_fault_asserted :1, ichs_fan_fault_asserted :1, ichs_identify_state :2, ichs_identify_supported :1, __reserved3 :1); } ipmi_chassis_status_t; extern ipmi_chassis_status_t *ipmi_chassis_status(ipmi_handle_t *); /* * See section 28.5 */ #define IPMI_CMD_CHASSIS_IDENTIFY 0x04 int ipmi_chassis_identify(ipmi_handle_t *, boolean_t); #pragma pack() #ifdef __cplusplus } #endif #endif /* _LIBIPMI_H */